Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Frisco
Furnace repair in Frisco typically runs $150 to $700 depending on the part that failed, and most no-heat calls we handle in Frisco are back up and running same day. If your furnace is blowing cold air, short-cycling, or making a sound it shouldn’t, call us at (361) 306-9515 and you’ll get a live person, not a voicemail queue. We dispatch from the Dallas-Fort Worth office, and our crews serve Frisco neighborhoods from Stonebriar to Frisco Lakes every day.
Frisco sits in Collin County’s hail-and-freeze corridor. That means the same homes that run furnaces hard during January ice events also see their attic-mounted equipment baked at 140°F in July. A repair-versus-replace call here has to weigh both seasons, not just one. Our Furnace Repair team sizes up the whole system, not just the part that quit.
Why Dalton Heating & Air Is Frisco’s Preferred Furnace Repair Company
Frisco homeowners call us because the price is in writing before any work starts. That’s not a promotion; it’s how every job goes, on every call, without exception. Marco Benitez leads our team, and he holds every tech to The Garrison Standard: arrive inside the stated window, put the price on paper, do the job by the book, leave the site clean, stand behind the work for a full year.
We’ve been operating since 2003 as a Garrison Partners company. The crews that show up in Frisco are background-checked and uniformed, and you’ll know who’s coming before they arrive. When a furnace fails during a Collin County cold snap, you don’t have time for a company that can’t answer the phone. Ours is staffed by a live person 24 hours a day, 7 days a week.
Technicians are factory-trained to service nine major residential HVAC brands. That matters in Frisco, where tract homes west of the Dallas North Tollway were often built with whatever furnace the builder’s supply house had on hand, and we see a mix of everything from Goodman to Carrier to Rheem.
Furnace Maintenance in Frisco
Furnace Maintenance in Frisco keeps a heating system from turning into a middle-of-the-night no-heat call when temperatures drop into the 20s. A tune-up runs $80 to $200 at Dalton and includes a written report of what we actually found, good and bad. Our techs are not paid on what they sell, so you won’t get a scare pitch off a clean unit.
What a Frisco tune-up covers
We clean and inspect the burner assembly, check the ignitor and flame sensor, test the blower motor’s capacitor, measure the temperature rise across the heat exchanger, and run the system through a full cycle. Frisco furnaces that sat idle through the warm fall often fire for the first time after the first hard freeze. That first cold snap is when ignitors and flame sensors fail, and we recommend getting ahead of it in October or early November.
When to schedule in Frisco
Book before the January ice events. Last winter’s pattern across Collin County pushed every HVAC company’s schedule back by days, and the homeowners who got heat fastest were the ones already on our maintenance list. A tune-up takes under an hour and gives you a clean baseline before the season that runs your furnace hardest.
Heat Pump Repair in Frisco
Heat Pump Repair in Frisco matters because a growing share of newer homes here, especially in PGA Frisco and the developments along Eldorado Parkway, run heat pumps instead of gas furnaces. The same unit that heats in winter cools in summer, and in Frisco’s climate it can run nearly year-round. That doubles the wear on every component.
Heat pump or furnace in a Frisco home
A heat pump moves heat instead of burning fuel. In mild Collin County weather it’s efficient and quiet. But when an ice event hits and the backup heat strips have to carry the load, a dirty coil or a bad reversing valve shows up fast. If your heat pump is running constantly or the air feels lukewarm, call before the weekend cold front.
What heat pump repair costs in Frisco
Heat pump repairs in Frisco run the same $150 to $700 range as furnace work, depending on the part. Reversing valves and compressor capacitors cost more than sensors and ignitors. Dalton puts the exact price in writing before we start the repair, and the work is guaranteed in writing for a full year. If it fails in that window, we come back at no charge.
Trusted Brands We Service in Frisco
Dalton technicians work on Goodman, Rheem, and York furnaces and heat pumps across Frisco every week. We keep common parts stocked on our trucks so a no-heat call in The Trails or Stonebriar doesn’t wait on a supply-house run, and we can source Daikin and other brand-specific components fast through our Dallas-Fort Worth supply lines. Since we’re factory-trained across nine major residential brands, there’s no “we don’t work on those” answer when you call.
Common Furnace Repair Problems We See in Frisco Homes
- Ignitor and flame-sensor failures after an ice event. Furnaces that sat idle all fall fire for the first time in a 20°F snap, and that first ignition cycle is when these parts fail. We see a spike in these calls every January across Frisco.
- Cracked heat exchangers on older units in tight attics. Frisco’s newer builds are well-insulated and often put the furnace in an attic that hits 140°F in July. A 15-year-old unit running hot year-round cracks its heat exchanger faster than a basement install would.
- Short-cycling from an oversized builder-installed furnace. Tract homes west of the Dallas North Tollway frequently have furnaces larger than the load calculation called for. The furnace reaches temperature too fast, shuts off, and cycles again. It wears out faster and leaves cold spots in the house.
- Blower motor capacitor failures. The capacitor that starts the blower motor is a $150 fix that looks like a big problem when it fails: the furnace runs but no air moves. We check the capacitor before recommending anything larger.
Pricing for Furnace Repair in Frisco, TX
Most furnace repairs in Frisco run $150 to $700. An ignitor or flame sensor replacement sits at the low end, usually $150 to $250. A blower motor or gas valve runs toward the middle and upper end. A full heat exchanger replacement can exceed $700 and often sparks the repair-versus-replace conversation, especially on a unit past 15 years old.
Here’s the honest breakdown for Frisco:
| Service | Frisco Price Range |
|---|---|
| Furnace Repair | $150 – $700 |
| Tune-Up | $80 – $200 |
| AC Repair | $150 – $650 |
| AC Installation | $3500 – $7500 |
Not sure if a repair is worth it? We’ll tell you straight. If the fix costs more than a third of a replacement and the unit is past 12 years old, we walk you through the math on both options. Estimates are free. Call (361) 306-9515.
We Also Serve Cities Near Frisco
Beyond Frisco, our crews run service calls to Prosper, Aubrey, Little Elm, and Celina. If you’re a few exits up the Dallas North Tollway or over on Highway 380, we’re already covering your neighborhood.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Frisco
Replace when the repair costs more than about a third of a new system and the furnace is past 12 years old. Our tech got a no-heat call off Eldorado Parkway in Frisco Lakes where a 14-year-old Goodman was short-cycling; the ignitor was fine, but the heat exchanger showed cracks and the blower motor’s capacitor read out of spec. We walked them through a load calculation before quoting a replacement, because throwing parts at a furnace past its service life doesn’t serve anyone. Call (361) 306-9515 and we’ll give you the same straight answer.
Most furnace repairs in Frisco run $150 to $700. Minor fixes like ignitor and flame-sensor replacements sit at $150 to $250. Blower motors, gas valves, and circuit boards land in the $300 to $600 range. The price is in writing before any work starts, and every repair carries a written one-year guarantee with a free return visit if the fix fails.
SEER2 is the newer, stricter efficiency rating for cooling and for heat pumps. In Frisco, where summer cooling costs between May and October run hard, a jump from a 14 SEER to a 16 SEER2 unit can cut cooling energy use by roughly 12 to 15 percent. The heating seasons matter, too: a heat pump’s heating efficiency, measured as HSPF2, determines how much backup heat you burn during an ice event. A proper load calculation tells you what you actually need, not what a builder ordered.
Short-cycling means the furnace fires, runs a few minutes, shuts off, and repeats. In Frisco tract homes west of the Dallas North Tollway, the most common cause is an oversized furnace installed by a builder who skipped a load calculation. It can also be a dirty flame sensor, a failing thermostat, or a clogged filter. We’ll find the cause before replacing anything, and the fee is the same diagnostic you’d pay on any service call.
We answer the phone 24/7 with a real person, and we get a tech to most Frisco neighborhoods same day for no-heat calls. When a cold front settles over Collin County, our schedule tightens, which is why our maintenance customers get priority routing. If your furnace quits in the middle of the night, call (361) 306-9515 and tell the dispatcher it’s a no-heat emergency.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Frisco since 2003.