Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Frisco
A heat pump installation in Frisco typically runs $3,500 to $7,500 when the job includes a proper load calculation and duct evaluation, and most replacements take one to two days once equipment is on hand. That price is in writing before any work starts, which is how we operate on every job, without exception. If you’re weighing repair versus replacement after a Frisco winter cold snap or a brutal July stretch, call us at (361) 306-9515 for a straight answer and a free estimate. We serve Frisco neighborhoods from Phillips Creek Ranch to Stonebriar to The Trails, and we know what these homes actually need because we work in them every week.
Why Dalton Heating & Air Is Frisco’s Preferred Heat Pump Installation Company
Frisco homeowners ask us to handle their heat pump work because we show up inside the stated window, put the price in writing before touching a screw, and stand behind the finished install for a full year under our 365-Day Done Right Promise. If something isn’t right, we make it right. That’s not a tagline; it’s the Garrison Standard we’ve been held to since 2003.
Marco Benitez leads our team, and he has built the Frisco operation around a simple rule: never let a homeowner guess who’s coming or what the job will cost. Every technician is background-checked and uniformed. You’ll know the name of the person at your door before they arrive. For heat pump work specifically, that matters because this equipment has more failure points than a basic AC – refrigerant circuits, reversing valves, defrost boards – and the person diagnosing it needs to know all nine major residential brands, which our techs do: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard.
We also answer the phone with a live person 24 hours a day, seven days a week. No voicemail queue. If your heat pump goes down during a February freeze and you live off Eldorado Parkway, you’ll talk to a human who can get a truck rolling.
Ductless Heat Pump Installation in Frisco
Ductless Heat Pump Installation is often the right call when a Frisco homeowner has a room that never keeps up – a second-story bonus room over the garage, a sunroom added in the 2010s, or a home office in a converted attic space off Coit Road. A ductless system mounts a compact indoor unit on the wall and connects it to a slim outdoor condenser with a small refrigerant line, so there’s no need to run new ductwork through finished ceilings. In Frisco’s existing housing stock, that’s frequently the difference between a one-day job and a two-week demolition project.
When Ductless Beats Extending Ductwork
If the existing ducts are already undersized for a heat pump’s higher airflow, tapping into them makes the original problem worse. We see this in older Frisco homes where the ductwork was sized for a gas furnace, and adding load just drives up static pressure. A ductless mini split avoids that entirely and gets the new space cooling and heating on its own thermostat.
What Ductless Work Costs in Frisco
Single-zone ductless heat pump installs in Frisco typically land in the $3,500 to $5,500 range depending on equipment and line-set run. Multi-zone systems run higher, closer to $7,500, especially when the outdoor unit serves three or four indoor heads. The written price covers everything – no change orders at the door.
Heat Pump Service in Frisco
Heat Pump Service in Frisco means diagnosing the full system, not just topping off refrigerant and hoping for the best. A heat pump runs year-round, which means it accumulates wear in July and February alike. Service calls in Frisco typically run $150 to $650 depending on the failed part, and the repair is guaranteed in writing for a full year. If it fails again inside that window, we return at no charge – that’s the free second visit, not an upgrade.
What a Service Call Covers
Our technicians check refrigerant charge, capacitor health, reversing valve operation, defrost board function, and airflow through the indoor coil. That last one catches a lot of problems early, especially on Frisco homes where the ductwork was built for a furnace and has been fighting a heat pump ever since. The price is fixed in writing before any work starts.
When Service Becomes Replacement
If a compressor fails on a 14-year-old unit, replacing it can cost more than the equipment is worth. We show you the repair number and the replacement number side by side and let you decide. No pressure, no upsell. Marco Benitez is clear with the team: technicians are not paid on what they sell, and that shows in the recommendations you get.
Trusted Brands We Service in Frisco
We’re factory-trained on the equipment we touch, and that includes the major names Frisco homes already have installed: Trane, Lennox, Goodman, and Rheem among them. If your current heat pump is one of those, we stock common replacement parts locally for faster turnaround – no waiting a week on a reversing valve or defrost sensor when the weather turns. And because we service what we install under one roof, you won’t get handed off between a sales company and a separate service outfit. Same crew, same standard, same phone number.
Common Heat Pump Installation Problems We See in Frisco Homes
- Oversized units installed off square footage alone. A heat pump that’s 1.5 tons too big short-cycles, never controls humidity, and burns through the compressor early. We correct this with a room-by-room load calculation instead of guessing off the old nameplate.
- Undersized ductwork paired with a new heat pump. Heat pumps push higher airflow than the gas furnaces many Frisco homes were built around. If the ducts can’t move the CFM, you get high static pressure, noisy registers, and an evaporator coil that starves for air.
- Neglected defrost boards and outdoor coils after a bad cold snap. Ice builds up on the condenser, the defrost cycle fails, and the homeowner is left with a no-heat call in February. Regular service catches this before the cold does.
- Mis-matched thermostat staging. A variable-speed heat pump driven by a single-stage thermostat never leaves its highest stage, which defeats the efficiency you paid for. We calibrate staging to match the load on every install.
Pricing for Heat Pump Installation in Frisco, TX
Here are the real numbers for Frisco. A full heat pump replacement with a proper Manual J load calculation and duct evaluation runs $3,500 to $7,500. Repair and service calls land between $150 and $650. A tune-up is $80 to $200. What moves the install number is equipment staging (single vs. variable speed), duct modifications if airflow is short, and whether you’re going with a ductless setup. We’ll put every line item on paper before anything is ordered so you know exactly what you’re paying and why. Call (361) 306-9515 for a free estimate.
| Service | Frisco Price Range |
|---|---|
| Heat Pump Installation (with load calculation and duct evaluation) | $3,500 – $7,500 |
| Heat Pump Repair / Service Call | $150 – $650 |
| Heat Pump Tune-Up | $80 – $200 |
The one variable most Frisco homeowners don’t expect is ductwork. We’ve replaced enough systems in homes off Stonebrook Parkway and around Lebanon Road to know that the old duct sizing is often the real problem. That’s why we include a static pressure reading with every install quote – it tells us whether the new heat pump will actually deliver what the efficiency sticker promises.
We Also Serve Cities Near Frisco
Our Heat Pump Installation team runs routes through Prosper, Aubrey, Little Elm, and Celina on top of our Frisco coverage. If you’re just over the city line and wondering whether we’ll come out, the answer is yes – same pricing, same written guarantee, same crew standards. And for the full picture on our Heat Pump Installation in Frisco work, that page covers the local details.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Frisco
You need the load calculation, especially in Frisco, where a lot of the existing systems going back a decade or more were oversized off square footage rather than measured. Matching the old tonnage just repeats the mistake – you get the same short-cycling, the same humidity problems, and the same early compressor failure. A Manual J plus a static pressure reading tells us what the house actually needs, and we include it with every install quote. Call (361) 306-9515 to schedule yours.
SEER2 is the updated efficiency testing standard that took effect in 2023, and it gives a more realistic number for real-world ductwork and airflow than the old SEER rating did. In Frisco, where summer cooling runs hard for five months straight and winter heat pumps cycle through cold snaps, a unit rated under SEER2 will typically perform closer to its sticker than one rated under the old method. It also means some older equipment that looked efficient on paper won’t meet the new baseline, so replacement pricing needs to account for that. We’ll show you the SEER2 numbers for whatever we quote.
Most cold-weather heat pump failures in Frisco are repairable, and the service call runs $150 to $650 depending on the part. A failed defrost board, weak capacitor, or low refrigerant charge are the usual culprits and each is a straightforward fix. If the compressor itself is done and the unit is over 12 years old, replacement starts making more sense. We’ll show you both numbers and let you decide. For an emergency call during a freeze, reach us at (361) 306-9515 – a live person answers 24/7.
Yes, and it’s a common job in Frisco homes with bonus rooms, converted garages, or second-story spaces the main system never quite handles. A ductless setup gets that room its own thermostat and its own heat pump, without touching the existing ductwork. Single-zone installs start around $3,500 in this market, and the written price covers the equipment, the line set, the electrical, and the commissioning so the staging matches the room load.
Twice a year is the right cadence in Frisco – once in early spring before the cooling season, once in late fall before the first freeze. A heat pump runs year-round, which doubles the wear on the compressor and coils compared to a cooling-only AC. A tune-up runs $80 to $200 and catches things like low refrigerant, failing capacitors, and dirty coils before they turn into a $650 repair call or a no-heat night in February.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Frisco since 2003.
Ready for a straight answer on your heat pump? Call (361) 306-9515 for a free estimate. We’ll put the price in writing before any work starts, and if it’s an emergency, a live person answers now.