Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Edgewood
Heat pump installation in Edgewood typically runs $3,500 – $7,500 for a full system, and most jobs are completed in one day once equipment is on-site. The real variable in Edgewood isn’t the unit itself, it’s whether your existing ductwork, thermostat wiring, and electrical panel are actually ready for a modern heat pump. Many aren’t, and that’s where a lot of installers cut corners. We don’t.
Dalton Heating & Air serves Edgewood, MD from our Baltimore dispatch office, with crews that know the neighborhoods off Pulaski Highway, Edgewood Road, and Hanson Road. When you call (361) 306-9515, you get a live person, a written price before work starts, and an install window we actually hit. The Garrison Standard has been our operating rule since 2003.
Why Dalton Heating & Air Is Edgewood’s Preferred Heat Pump Installation Company
Marco Benitez leads our Edgewood installation work, and he runs crews under one non-negotiable rule: the price is in writing before anyone touches a screwdriver. That’s The Garrison Code, and it’s why Edgewood homeowners who’ve been burned by no-shows and door-pricing call us back.
Our techs arrive background-checked and in uniform, driving trucks stocked with the parts needed for most Edgewood heat pump jobs. That means fewer return trips. We service all nine major residential HVAC brands, including Goodman, Rheem, and York, so we’re not married to selling you one particular nameplate. The unit gets spec’d to your house, not our warehouse.
Every heat pump installation from Dalton Heating & Air includes our 365-Day Done Right Promise. If it’s not right in the first year, we make it right. That’s the entire guarantee, in writing, on every job.
Heat Pump Service in Edgewood
Heat Pump Service in Edgewood is what you need when your system is running but not running right: short cycling, weak airflow, ice on the coil, or a compressor that won’t kick over. Most heat pump service calls in Edgewood run $150 – $650 depending on the part and the labor. The first question we always answer is repair versus replace, and we answer it with a written diagnostic, not a sales script.
Diagnostic First, Honest Number Second
We show up, check refrigerant pressures, electrical draw, airflow, and thermostat behavior, then tell you what’s actually wrong. If the fix is a $200 capacitor, that’s what we quote. If the existing unit is a 15-year-old R-22 system with a failing compressor, we’ll tell you replacement is the smarter money. The Garrison Standard means we put that recommendation in writing before you spend anything.
Older Edgewood Homes Need Specific Attention
Plenty of Edgewood’s housing stock dates to the 1960s and 1970s. A significant number of those systems still run on original wiring that lacks a common wire. Without it, a modern heat pump’s defrost board can’t signal auxiliary heat properly during a cold snap. Our techs check for this on every service call because a new heat pump on old thermostat wiring is a service failure waiting to happen.
Heat Pump Replacement in Edgewood
Heat Pump Replacement in Edgewood means pulling out an old system and putting in a properly sized, properly matched heat pump with the thermostat wiring and duct connections it actually needs. A full replacement in Edgewood runs $3,500 – $7,500. That range reflects the difference between a standard single-stage swap and a variable-speed system with a matched evaporator coil and corrected ductwork.
Why We Don’t Match Old Tonnage
The biggest mistake we see in Edgewood replacements is sizing the new heat pump to the old AC nameplate instead of a room-by-room load calculation. Many Edgewood homes had their ductwork installed when insulation was thinner and windows were leakier. Oversized equipment short cycles, runs constantly in the summer, and never dehumidifies properly. We run the load calculation on every replacement and spec the equipment to your actual house, not your old unit’s label.
Static Pressure and Ductwork Checks
Before we order equipment, we check the static pressure your existing ductwork can handle. If it’s undersized, a standard air handler will strain the blower motor and under-deliver. Sometimes the fix is minor, like a corrected return drop. Sometimes it’s a variable-speed air handler that can work within your duct pressure. Either way, it’s handled before install day, not discovered after.
We recently sent a tech to a 1970s ranch near Edgewood Road where the old condenser had failed and the homeowner wanted a heat pump. Our load calculation showed the ductwork couldn’t handle the static pressure of a standard 3-ton air handler without major modifications. We spec’d a variable-speed Carrier unit with a matched evaporator coil and corrected the return drop. After commissioning, the system hit its rated SEER2 numbers and cut the winter electric bill by roughly a third compared to the old resistance heat. That’s what a proper Heat Pump Installation looks like.
Trusted Brands We Service in Edgewood
We install and service heat pumps from Goodman, Rheem, York, and Daikin, along with five other major residential brands. Our Baltimore warehouse stocks common parts for these nameplates, which means we’re not waiting a week on a defrost board when your system goes down in January. For Edgewood homeowners, that local parts access translates to faster repairs and fewer days without heat. We’ll recommend the brand and model that matches your house’s load calculation and your budget, and we’ll put that recommendation in writing before any money changes hands.
Common Heat Pump Installation Problems We See in Edgewood Homes
- Thermostat wiring without a common wire. Many older Edgewood homes have wiring that can’t power a modern thermostat’s constant draw, so the heat pump’s defrost board can’t signal auxiliary heat properly during Edgewood’s cold snaps.
- Undersized ductwork for the new system’s airflow. High static pressure reduces capacity, strains the blower motor, and shortens equipment life. This is one of the most common failures we find on installs done by crews that skipped the duct check.
- Oversized replacement tonnage based on the old AC nameplate. Short cycling and poor dehumidification follow within a season, especially during Edgewood’s humid summers. A room-by-room load calculation prevents this.
- No commissioning after install. A heat pump that isn’t checked for correct refrigerant charge and airflow may run, but it won’t hit its rated efficiency. We commission every system and verify the numbers before we leave.
Pricing for Heat Pump Installation in Edgewood, MD
Here are the real numbers for Edgewood, MD. These are the same ranges we quote across our Maryland service area, and they’re backed by a written estimate before any work begins.
| Service | Edgewood Price Range |
|---|---|
| Heat Pump Installation (full system) | $3,500 – $7,500 |
| Heat Pump Service (diagnostic/repair) | $150 – $650 |
What moves the number inside that range? Equipment efficiency level, ductwork modifications, thermostat and wiring upgrades, and whether your electrical panel needs a new circuit. A basic single-stage swap in a home with modern wiring lands near the bottom. A variable-speed system with duct corrections and new thermostat wiring lands near the top. Either way, you get the exact price in writing before the install starts, and that price doesn’t change at the door. Call (361) 306-9515 for a free estimate on your Edgewood heat pump installation.
We Also Serve Cities Near Edgewood
Dalton Heating & Air handles Heat Pump Installation in Edgewood and the surrounding communities, including Abingdon, Kingsville, White Marsh, and Perry Hall. If you’re just outside Edgewood and need a straight answer on heat pump service or replacement, call us and ask for Marco’s team. We dispatch from Baltimore and run crews through this area daily.
Serving Edgewood, MD - Our Local Coverage Area
We’re based in the Edgewood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Edgewood
The honest answer is that it comes down to the compressor, the age of the system, and whether it uses R-22 refrigerant. If the compressor is sound and the unit is under 12 years old, repair usually makes sense, and most heat pump repairs in Edgewood run $150 – $650. If the compressor has failed or the system is older and runs on R-22, replacement is generally the better long-term move, and a full heat pump replacement in Edgewood runs $3,500 – $7,500. We give you the diagnostic in writing before you decide. Call (361) 306-9515 and we’ll walk you through the actual numbers on your unit.
Edgewood’s housing stock is a mix of 1960s and 1970s ranches and split-levels, many with original ductwork and insulation. A load calculation accounts for your actual building envelope, window area, and duct capacity, which means you get a heat pump sized for your house, not the old unit’s nameplate. Skip the calculation and you risk short cycling in Edgewood’s humid summers and poor dehumidification. We run it on every installation.
SEER2 is the updated efficiency rating for heat pumps, measuring how much cooling you get per watt of electricity. Higher SEER2 ratings use less power, which matters in Edgewood because heat pumps here run for both summer cooling and winter heating. A jump from a 14 SEER2 unit to an 18 SEER2 unit can reduce your cooling-season electric use by 20% or more. We’ll show you the rated numbers and explain what they mean for your specific utility bill.
In Edgewood’s older homes, the most common cause is thermostat wiring that lacks a common wire, which prevents the defrost board from signaling auxiliary heat correctly during cold snaps. Other causes include a failing reversing valve or low refrigerant charge. This is a service call, not a DIY fix, and most heat pump service in Edgewood runs $150 – $650. Call (361) 306-9515 and we’ll diagnose it properly.
Yes, and we do it the way the older Edgewood housing stock requires. That means checking the existing ductwork’s static pressure, verifying the thermostat wiring, and running a load calculation before we order any equipment. If the ducts can’t handle a standard air handler, we’ll spec a variable-speed unit or correct the return drop. The written quote includes whatever modifications the house actually needs.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Edgewood, MD.