Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Roanoke
Furnace repair in Roanoke typically runs $150 to $700 depending on the part that failed, and most jobs are completed the same day we arrive. If your furnace is blowing cold air, short-cycling, or making noise it didn’t make last winter, call us at (361) 306-9515. We answer the phone with a live person, every hour of every day, and we’ll give you a written price before any work starts.
Dalton Heating & Air works up and down the US 377 corridor daily, from older homes near Oak Street to new subdivisions going up around the Roanoke Hills area. We know the housing stock here: 1990s tract homes, custom builds on acreage, and everything in between. That matters because the right furnace repair in Roanoke depends as much on how your house was built as it does on what brand of furnace sits in the closet.
Why Dalton Heating & Air Is Roanoke’s Preferred Furnace Repair Company
We built our reputation in Roanoke one no-heat call at a time. Homeowners here tell us the same story: another company quoted a low number on the phone, then doubled it at the door. That doesn’t happen with us. The price is in writing before we touch a single component, and it’s the same price whether the call takes forty minutes or four hours.
Every Dalton technician shows up in uniform, background-checked, and factory-trained to service Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. Dispatch and scheduling run through our Dallas-Fort Worth office; the crews serving Roanoke live and work in this area. When a furnace fails on a cold night in the 76262 zip code, we’re not driving from across the metroplex. That’s why our response time to Roanoke is measured in hours, not days.
We run every call under The Garrison Standard, a code set by our parent company in 2003. Arrive inside the stated window. Put the price in writing before starting. Do the job by the book. Leave the site clean. Stand behind the work for a full year. If a repair fails inside that year, we return at no charge. That’s a written guarantee, not a verbal promise.
Heat Pump Repair in Roanoke
Heat pump repair in Roanoke means diagnosing a system that both heats and cools, so the failure mode can show up in either season. Most heat pump failures we see here involve the reversing valve, the defrost control board, or low refrigerant levels from a slow leak. Repair costs run the same $150 to $700 range as furnace work, with the specific number tied to the part and labor involved.
Roanoke’s winter temperatures hover close to the point where heat pumps lose efficiency, so a system that’s been marginal for years tends to show it first on the coldest nights. If your heat pump runs constantly but can’t hold set temperature, the problem is rarely the thermostat. It’s usually airflow, refrigerant charge, or a control board that isn’t telling the outdoor unit to cycle properly.
When a Heat Pump Needs More Than a Part
Some heat pump issues point to the replacement conversation. A compressor nearing the end of its life, a refrigerant leak that’s already been patched once, or an indoor air handler that wasn’t sized right from day one. We’ll show you the numbers on repair versus replace, with real dollar figures, and you decide. Nobody in a Roanoke living room gets pressured by our team.
What a Proper Heat Pump Diagnosis Looks Like
We check static pressure, temperature rise, refrigerant pressures, and electrical draw before we quote a repair. That takes time, but it prevents replacing a part that wasn’t the actual problem. A ten-minute diagnosis on a heat pump is a guess, not a diagnosis, and Roanoke homeowners pay for guesses in repeat calls.
Heating Repair in Roanoke
Heating repair in Roanoke covers everything from a cracked heat exchanger in a gas furnace to a failed blower motor in an air handler. When your house is cold and the system won’t respond, that’s a heating emergency, and it’s one of the few times we’ll say plainly: speed matters. A family with no heat on a 25-degree night needs a technician now, not a callback window.
Most heating repairs in Roanoke run $150 to $700. The spread exists because a flame sensor replacement costs far less than a heat exchanger or a variable-speed blower motor. We’ll tell you exactly which part failed, what it costs, and what your options are, before you authorize anything.
Furnace Heating Systems
Gas furnaces in Roanoke tend to fail in predictable ways: ignitor burnout, flame sensor fouling, pressure switch trips, and inducer motor failures. Older furnaces in 1990s-era homes around Roanoke’s established neighborhoods run into a different problem: heat exchangers that have been running hot for decades because the furnace was oversized for the ductwork. We check for that on every call.
Heat Pump and Electric Heat
Electric heat strips and heat pump systems fail differently from gas furnaces. Sequencers stick, limits trip, and strip elements burn out. In Roanoke’s newer builds, where all-electric systems are common, these are routine fixes. The parts are less expensive than gas furnace components, but the diagnostic work is just as important.
Trusted Brands We Service in Roanoke
Our technicians are factory-trained on nine major brands, including Rheem, York, Daikin, and Bryant. That’s not a marketing claim; it means we know the wiring diagrams, the failure patterns, and the correct diagnostic sequence for each manufacturer. We stock common furnace parts for all four of those brands in our service vehicles, which means fewer second trips and faster restorations of heat when you’re waiting in a cold house. When a Rheem control board fails in Roanoke, we’re not ordering the part and hoping it arrives by Friday. We usually have it on the truck.
Common Furnace Repair Problems We See in Roanoke Homes
- Short-cycling from undersized returns. Older Roanoke homes frequently have return ductwork that was never designed for the furnace’s airflow requirements. The furnace runs hot, trips its limit switch, and shuts down early. We measure static pressure to catch this before it cracks a heat exchanger.
- Heat exchanger cracks from oversized furnaces. Tract homes built before the current code cycle often got furnaces sized on square footage alone, with no load calculation. An oversized furnace cycles constantly, stresses the metal, and eventually cracks. This is the difference between a $200 repair and a $4,000 replacement, and we check for it on every tune-up and repair call in Roanoke.
- Thermostat calibration drift. Sometimes the furnace is fine and the thermostat is lying. Older mechanical thermostats and even some digital models drift out of calibration over time, so the system can’t tell when to call for heat. We verify thermostat accuracy before replacing expensive furnace components.
- Ignitor failures in gas furnaces. Hot surface ignitors are a wear item. They crack, they fail, and the furnace locks out. It’s a common problem across all brands and all Roanoke subdivisions, and it’s one of the more affordable repairs we do. The key is confirming the ignitor failed on its own, not because a gas valve is leaking or a pressure switch is intermittent.
We ran a no-heat call off Litsey Road where the homeowner’s Carrier furnace was short-cycling. A quick static pressure check showed the return was undersized for the tonnage of the system, and the heat exchanger was already showing stress cracks from years of running hot. We replaced the blower motor, corrected the return sizing, and showed the homeowner the before-and-after temperature rise on the thermostat so they could see the fix, not just hear it. That’s the kind of diagnosis that separates a real repair from a parts swap.
Pricing for Furnace Repair in Roanoke, TX
Here’s what furnace work costs in Roanoke, in plain numbers:
| Service | Typical Price Range |
|---|---|
| Furnace Repair | $150 – $700 |
| Furnace Tune-Up | $80 – $200 |
A flame sensor cleaning or ignitor replacement lands at the low end. A heat exchanger replacement, blower motor, or control board pushes toward the high end. Every quote includes the full written price before work starts. We don’t do “estimates” that turn into something else when we’re standing in your hallway. And if you want to know whether the repair is worth doing versus putting the money toward a new system, we’ll show you that math honestly, then leave the decision to you.
Call (361) 306-9515 for a free estimate. You’ll get a specific price range for your situation, and a real person on the phone who can answer questions.
We Also Serve Cities Near Roanoke
Our service area covers the communities around Roanoke, including Flower Mound, Southlake, Argyle, and Justin. If you’re in one of those cities, the same written pricing, same-day response, and one-year written guarantee apply. See our Furnace Repair page for the full scope of what we cover, or read more about Furnace Repair in Roanoke for local specifics.
Serving Roanoke, TX - Our Local Coverage Area
We’re based in the Roanoke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Roanoke
Yes, substantially. A 1990s home in Roanoke typically has ductwork sized for a furnace that may have been replaced once or twice, often with a unit that moves different airflow than the original design. A new-build home has tighter envelope standards and different static pressure characteristics. We start every diagnosis by measuring what your specific house is doing, not by applying a generic checklist. The furnace brand matters less than the house it’s installed in.
SEER2 is the updated efficiency testing standard for cooling equipment that went into effect in 2023, and it affects furnaces only when you’re pairing one with an air conditioner or heat pump. On a furnace repair, it matters for one reason: if your furnace is old enough that its paired AC doesn’t meet current minimums, spending $700 on a repair might be throwing money at a system that needs replacement inside two years anyway. We’ll tell you if that’s the case, with the numbers in front of you.
Most of the time, cold air from a furnace is a repair situation. A failed ignitor, a dirty flame sensor, a tripped limit switch, or a gas valve that lost its signal are all repairable for a few hundred dollars. The exception is a cracked heat exchanger, which is a safety issue and often makes replacement the honest recommendation. We’ll show you the crack, explain what it means, and give you both options with real prices. Call (361) 306-9515 and we’ll walk through what you’re seeing over the phone first.
The math is simpler than most homeowners expect. Take the repair cost and multiply it by the system’s age relative to its expected life. If your furnace is 12 years old and the repair is $600, that’s a real conversation. If it’s 7 years old and the repair is $200, fix it. We also factor in efficiency, because a 20-year-old furnace in Roanoke is burning more gas per degree of heat than a modern unit. You’ll see those numbers on your utility bill. Our job is to put the repair cost, the replacement cost, and the expected remaining life in front of you, then let you decide without pressure.
A $80 to $200 tune-up in Roanoke should include checking the heat exchanger for cracks, testing the ignitor and flame sensor, measuring gas pressure, checking static pressure, cleaning the burners, and verifying the thermostat’s calibration. If a company charges less and just changes the filter, that’s not a tune-up. Ours includes a written report of what we found, what’s in spec and what isn’t, and a written price for any recommended repair. No one pushes you to buy anything on the spot. Our technicians are not paid on what they sell.
Call Dalton Heating & Air for Furnace Repair in Roanoke
When your furnace quits in Roanoke, you don’t need a sales pitch. You need a technician who shows up, diagnoses the problem honestly, and puts the price in writing before touching anything. That’s what we do. Call (361) 306-9515 any time, day or night. A live person answers, we’ll get a technician to your Roanoke home fast, and the repair is guaranteed in writing for a full year. If it fails in that time, we come back at no charge. That’s The Garrison Standard, and it applies to every call we run in Roanoke.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Roanoke, TX since 2003.