Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Keene
A new heat pump installation in Keene typically runs $3,500 to $7,500 depending on the size of your home, the SEER2 efficiency rating you choose, and whether your existing ductwork needs correction. We serve homes throughout Keene from Cleburne to Joshua with written pricing before any work starts, so you know the full cost before we open a single panel. Call (361) 306-9515 and a live person answers, 24/7. No voicemail queue, no callback window.
Keene has a particular climate problem that generic HVAC outfits tend to miss. Summer design temperatures push past 100°F while winter nights still drop below freezing. That means a heat pump here has to be sized for a real heating load, not just copied off the cooling tonnage of your old condenser. We run a full load calculation on every installation in Keene. If a contractor skips that step and matches box-for-box, you end up with a unit that cools fine in July but can’t hold 68°F when a January cold snap hits Johnson County.
Why Dalton Heating & Air Is Keene’s Preferred Heat Pump Installation Company
Marco Benitez leads our Keene installations, and he’s the one who signs off on every job before we call it complete. Keene homeowners tell us the thing that convinced them to call was the written guarantee: every repair and installation is covered in writing for a full year. If a heat pump we install fails in that window, we return at no charge. That’s the 365-Day Done Right Promise, and it’s not an upsell. It’s standard on every job.
Our Keene customers also know who’s showing up before the truck pulls in. Background-checked, uniformed technicians on every call. The price is in writing before any work starts, on every job, without exception. We’re part of Garrison Partners, a network held to The Garrison Standard since 2003. That means the code we operate under is specific: arrive inside the stated window, price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year.
Dispatch and scheduling for Keene run through our Dallas-Fort Worth office, and crews serve Keene locally. When you call, you speak to a real person who knows the heat pump installation schedule for this area. Not a script.
Heat Pump Replacement in Keene
Heat Pump Replacement in Keene is usually the right call when your existing system is more than 12 years old, runs on R-22 refrigerant that’s no longer manufactured, or has needed multiple repairs in the last two seasons. We replaced a tired 2.5-ton Carrier condenser in the College Station-area homes off Old Betsy Road with a properly sized heat pump after the old unit kept tripping on a weak capacitor and a low refrigerant charge every August. A load calculation showed the ductwork was undersized for the new SEER2 equipment, so we corrected the static pressure and set the new thermostat calibration before we called it done. The homeowner’s summer peak kW draw dropped noticeably on the next bill.
That job is a textbook example of what goes wrong when you match tonnage instead of running the numbers. A straight swap would have left the same airflow problem, the same high static pressure, and the same premature compressor wear. Instead, the replacement actually fixed the root cause. That’s the difference between a box-for-box swap and a heat pump replacement done to The Garrison Code.
Cost for a heat pump replacement in Keene falls in the same $3,500 to $7,500 range as a new installation, because the labor to remove the old equipment and correct the ductwork is often the largest line item. What changes the number is the SEER2 rating you choose, whether your ductwork needs sealing or resizing, and whether your electrical panel has room for the new circuit. We give you a written fixed price before any work starts, so there’s no surprise on the final invoice.
The Load Calculation Difference
A proper Manual J load calculation measures your home’s square footage, window orientation, insulation levels, and air leakage. In Keene, where summer design temperatures exceed 100°F, skipping this step means guessing at cooling capacity. Guessing wrong means a unit that short-cycles in August.
Ductwork Correction on Older Keene Homes
Homes built before the 1990s across Keene often have duct systems sized for older, lower-efficiency equipment. A new high-SEER2 heat pump moves air differently. If we don’t check static pressure and correct the ductwork, you’ll never see the rated efficiency on your bill. We check it on every replacement.
Mini Split Installation in Keene
Mini Split Installation in Keene makes sense when you’re adding comfort to a room that was never on the original duct plan: a converted garage, a sunroom, a home office over a slab, or a mother-in-law suite. Ductless mini splits are heat pumps without ducts. The outdoor condenser connects to one or more indoor air handlers through a small line set, so you get zoned heating and cooling without tearing open walls to run ductwork.
For Keene homeowners with homes that have central HVAC but one chronically hot or cold room, a mini split is often cheaper than reworking the whole duct system. Installation cost typically lands between $3,500 and $7,500 depending on the number of indoor heads and the SEER2 rating. We install Rheem, York, and Bryant mini splits, among other brands we service.
The efficiency play is real. Duct losses account for 20 to 30 percent of the energy in a forced-air system. Mini splits eliminate that loss entirely by moving refrigerant directly to the room. For a Keene homeowner cooling a single room through a long, leaky duct run, the math often favors going ductless.
When Ductless Beats Ducted
If your existing ductwork is in bad shape or your home has no ducts at all, a mini split system can be installed in one to two days with minimal disruption. We also install multi-zone mini splits that handle up to five indoor heads from one outdoor unit. Each zone runs independently, so you’re not heating or cooling rooms nobody’s using.
SEER2 and Real Electric Bills
The SEER2 rating measures cooling efficiency under real-world conditions, not the old laboratory SEER standard. A higher SEER2 rating means a lower kW draw per hour of cooling. For a Keene summer that runs hard from May through September, that efficiency difference shows up as a real dollar amount on your CPS or Oncor bill depending on your electric provider.
Trusted Brands We Service in Keene
Our factory training covers nine major residential HVAC brands, including Rheem, York, Daikin, and Bryant. That matters in Keene because different homes need different equipment matchups. Bradford Park’s newer construction often works well with a high-efficiency Rheem heat pump, while some of the older homes near Old Betsy Road do better with a Bryant unit paired with corrected ductwork and a properly set blower speed. We stock common parts for these brands locally and can source equipment fast through our DFW supply chain. No waiting weeks for a condenser when the weather turns.
Common Heat Pump Installation Problems We See in Keene Homes
- Tonnage matching instead of load calculation. Replacing a heat pump by matching the old unit’s tonnage leaves the new one short on heating capacity when Keene winter nights dip below freezing. We run a full Manual J on every installation because a wrong-sized heat pump costs you comfort and money.
- Skipped static pressure checks on older ductwork. Many Keene homes have ducts sized for old, low-efficiency equipment. A new high-SEER2 heat pump with restricted ducts never reaches its rated efficiency, and the blower motor runs harder than it should, shortening its life.
- Weak capacitor or drifted refrigerant charge left uncorrected. A weak capacitor on the new condenser or a refrigerant charge that isn’t dialed in to manufacturer spec quietly shortens the life of the condenser coil and compressor. We check both during installation, not as an extra line item.
- Wrong thermostat calibration. A new heat pump with a thermostat that’s not calibrated to the specific equipment can short-cycle or never properly stage. We set the thermostat during installation and verify it operates correctly before we leave.
Pricing for Heat Pump Installation in Keene, TX
Here’s what you can expect to pay for heat pump and related work in Keene. These are written-price ranges, not door-knock estimates. We put the number in writing before any work begins.
| Service | Price Range in Keene |
|---|---|
| Heat Pump Installation | $3,500 – $7,500 |
| AC Installation | $3,500 – $7,500 |
| Tune-Up | $80 – $200 |
| AC Repair | $150 – $650 |
What moves a heat pump installation toward the top or bottom of that range: the SEER2 rating, the size of your home, whether ductwork needs correction, and whether your panel needs a new circuit. We give you a written fixed price before any work starts, and every estimate is free. Call (361) 306-9515 to schedule one.
We Also Serve Cities Near Keene
Our Keene customers often ask if we cover Cleburne, Joshua, Alvarado, and Burleson. Yes, we do. If you’re in one of those nearby communities and need heat pump work, learn more about our Heat Pump Installation services. We schedule routes through Johnson County every week, so response times stay short.
Serving Keene, TX - Our Local Coverage Area
We’re based in the Keene area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Keene
Replace when your heat pump is over 12 years old, runs on R-22 refrigerant, or has needed two or more repairs in the last 24 months. Repair when the unit is under 10 years old and the failure is a single part like a capacitor or a contactor. In Keene, where both summer cooling and winter heating loads are real, a failing heat pump is a health risk in extreme weather, not just an inconvenience. Call (361) 306-9515 and we’ll give you an honest read.
Most Keene homes need between 2.5 and 4 tons depending on square footage, insulation, and window orientation. The only way to know for certain is a Manual J load calculation, which we run on every installation. Guessing by matching your old condenser’s tonnage is exactly how homeowners end up with a unit that can’t hold temperature on a freezing winter night.
A new heat pump installation in Keene runs $3,500 to $7,500. The price varies by SEER2 rating, home size, ductwork condition, and whether your electrical panel needs work. We give you a written fixed price before any work starts, so you know the total before the first panel comes off.
Yes, if the installation is done correctly. A higher SEER2 heat pump draws fewer kilowatts per hour of cooling, which shows up as a lower electric bill during Keene’s long cooling season. But if your ductwork is undersized or your static pressure is too high, you’ll never see the rated efficiency. That’s why we check and correct ductwork on every install.
Yes, we install ductless mini splits throughout Keene. They make more sense when you’re heating or cooling a single room that was never on the duct plan, or when your existing ductwork is in poor condition and the cost to replace it exceeds the cost of going ductless. Installation runs $3,500 to $7,500 depending on the number of indoor heads.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Keene since 2003.