Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Denton
A full heat pump installation in Denton typically runs $3,500 to $7,500 depending on tonnage, efficiency rating, and ductwork condition, and most jobs take one to two days. That’s the honest number before anyone steps inside your house. Dalton Heating & Air puts the price in writing before the first tool comes off the truck, and every installation is backed by a full-year written guarantee under The Garrison Standard. Call (361) 306-9515 for a free estimate from Marco Benitez and our Denton installation team.
We work in Denton every week. We know the difference between a 1970s ranch off University Drive and a two-story build in Robson Ranch, and we know which heat pump sizing mistakes show up in each. When you call, a real person answers. When we set a window, we show up inside it.
Why Dalton Heating & Air Is Denton’s Preferred Heat Pump Installation Company
Dalton Heating & Air operates under The Garrison Code: arrive inside the stated window, price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. That’s not a marketing line. It’s the operating rule we’ve followed since 2003, and it applies to every heat pump we install in Denton, from Southridge to Oakmont.
Our techs are background-checked and uniformed, so you know who’s coming before they pull up. They’re factory-trained to service and install nine major residential HVAC brands, including Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. When a Denton homeowner needs a heat pump swapped in a 1990s neighborhood near Loop 288 or a new variable-speed unit in a custom home north of Rayzor Ranch, we show up with the right equipment and the right training.
If a heat pump repair fails within the guarantee period, we return at no charge. If the installation isn’t done right, we make it right under our 365-Day Done Right Promise. Those terms are written, not implied.
Heat Pump Maintenance in Denton
Heat Pump Maintenance in Denton matters more than in milder parts of Texas because this system runs year-round: cooling through 100-degree summers and heating through low-20s winter nights. A seasonal tune-up catches the small failures before they become a no-heat call in January or a no-cooling call in July. Most heat pump maintenance in Denton runs $80 to $200, which is cheap compared to a $650 compressor failure caused by a plugged filter and a dirty outdoor coil.
What Our Tune-Up Covers
We clean the condensate drain, check the refrigerant charge, test the reversing valve, measure static pressure, and inspect the electrical connections that loosen over time on a heat pump that cycles constantly. The thermostat gets calibrated too. You get a written report of what we found, and our technicians are not paid on what they sell.
Why Spring and Fall Matter Here
Denton’s shoulder seasons are when a heat pump short-cycles if the system is oversized or low on charge. A fall tune-up catches the charge issue before the first cold snap. A spring tune-up catches the cooling deficiency before the first 95-degree day. Two visits per year, under $200 each, and you avoid most emergency calls.
Geothermal Heat Pump Installation in Denton
Geothermal Heat Pump Installation in Denton is a bigger investment than an air-source system, but the North Texas ground temperature holds around 65 degrees year-round, which gives a ground-source loop a steady baseline whether it’s 15 degrees or 100 degrees outside. For newer Denton homes with enough lot space on the east side near Aubrey or on acreage north of Sanger, a horizontal loop field is a realistic option. For tighter lots, a vertical bore is the route, and that pushes cost up substantially.
What a Geothermal Job Involves
We drill or trench the loop field, run the loop to a water-to-air unit inside, and tie it into your existing ductwork. The installed cost exceeds the air-source range, often by a wide margin, but the operating cost drops because the compressor isn’t fighting a 100-degree outdoor coil in August. The 30% federal geothermal tax credit still applies in Texas, and we walk every Denton homeowner through that paperwork before the job starts.
Is It Right for Your Denton Home
If you’re planning to stay in the house for 10-plus years and you have the open ground, geothermal makes sense. If you’re in a tight-lot neighborhood near the UNT campus or off Dallas Drive, a high-efficiency air-source heat pump with a proper load calculation almost always makes more sense. Either way, the estimate comes in writing, and Marco Benitez gives you the straight answer, not a sales pitch.
Trusted Brands We Service in Denton
We install and service four of the most common heat pump brands in Denton homes: Goodman, Rheem, York, and Daikin. Each one has specific sizing quirks and control-board behavior, and our techs see enough of them in Denton that we don’t need a manual to diagnose a reversing valve failure on a Rheem or a defrost control issue on a Goodman. We keep common parts stocked on our trucks serving the Denton area, so a repair in Argyle or west Denton doesn’t wait on a parts shipment from DFW.
Common Heat Pump Installation Problems We See in Denton Homes
- Undersized units selected from square footage alone. A 1,600-square-foot 1980s home off Hickory Creek Road with original single-pane windows loses heat differently than a 1,600-square-foot 2015 build. When a contractor skips the load calculation and drops in a 2.5-ton unit, the auxiliary heat carries too much of the load during Denton’s December and January cold snaps. Your electric bill shows the truth.
- New variable-speed units on old ductwork never sized for the static pressure. We see this constantly in 1970s and 1980s Denton subdivisions where the original metal ducts are undersized. A modern variable-speed air handler pushes against that restriction, head pressure climbs, and the blower motor burns out early. Sometimes the right move is duct modification before the heat pump goes in.
- Oversized tonnage causing short cycling in shoulder seasons. Denton’s mild spring and fall days don’t demand much from a heat pump. If the unit is oversized for the actual load, it satisfies the thermostat too fast and shuts down. Short cycles cook compressors over time. A room-by-room load calculation prevents this.
- Duct leakage in pier-and-beam homes. Plenty of older Denton homes south of I-35E sit on pier-and-beam foundations. Ductwork in the crawlspace leaks, and a new heat pump pushing conditioned air through leaky ducts wastes 20 to 30 percent of its output. We test static pressure and duct tightness on every installation, not just the equipment.
Pricing for Heat Pump Installation in Denton, TX
Here’s what the numbers look like in Denton:
| Job | Price Range |
|---|---|
| Heat Pump Installation (full system) | $3,500 – $7,500 |
| Heat Pump Repair / diagnostic and component replacement | $150 – $650 |
| Heat Pump Maintenance / seasonal tune-up | $80 – $200 |
What moves a Denton heat pump install across that $3,500 to $7,500 band? Tonnage, SEER2 rating, brand, and whether the existing ductwork can handle a modern variable-speed system. A basic 14.3 SEER2 Goodman in a small rental near the UNT campus lands on the low end. A 16-plus SEER2 Daikin with duct modifications in a 2,800-square-foot home near Robson Ranch lands higher. Every quote is free, and every quote is in writing before you agree to anything. Call (361) 306-9515.
We Also Serve Cities Near Denton
Our Heat Pump Installation crews run regularly to Krum, Argyle, Sanger, and Aubrey. Same written pricing, same full-year guarantee, same on-time window. If you’re in any of those towns and need a straight answer on a heat pump, call the same number and ask for Denton dispatch.
Serving Denton, TX - Our Local Coverage Area
We’re based in the Denton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Denton
Yes, you need a load calculation. Denton’s climate swings from 95 to 100-degree cooling design to low-20s heating design, which is a much wider band than Gulf Coast metros, so a rule-of-thumb tonnage match fails often. The old unit may have been wrong from day one, so matching it doubles down on the mistake. We run a Manual J room-by-room calculation on every installation, and we check duct static pressure at the same time. Call (361) 306-9515 for a free estimate that includes the load calculation.
A 12-year-old heat pump in Denton is at the end of its realistic service life, especially if it’s been cycling through Denton summers since 2012. If the repair quote is under $650 and the compressor is quiet and holding charge, a repair buys you another season or two. If the repair is north of $650 or the compressor or reversing valve is involved, replacement is usually the smarter math. We’ll tell you which one applies to your unit, with the numbers in front of you. Call (361) 306-9515 and we’ll walk you through it.
SEER2 is a revised efficiency rating that accounts for real-world duct pressure, and a 15.2 SEER2 unit will pull about 20 to 25 percent less electricity than a 10 or 11 SEER unit from the mid-2010s. For a Denton homeowner running a heat pump 300-plus days per year between heating and cooling, that’s a real difference on the Denton Municipal Electric bill. Higher SEER2 costs more upfront, so the math depends on how long you plan to stay in the house.
A typical 1,800 to 2,200-square-foot Denton home lands in the 3 to 3.5-ton range, but the actual number depends on insulation, window orientation, air leakage, and duct condition. A 1975 ranch on Windsor Drive needs a different tonnage than a 2015 two-story in Robson Ranch. We won’t quote you a tonnage until we’ve run the load calculation, because quoting from square footage alone is how undersized and oversized systems get installed.
We install and service Goodman, Rheem, York, and Daikin heat pumps in Denton, and we’re factory-trained across nine major residential HVAC brands total, including Carrier, Trane, Lennox, and Bryant. That means we’re not married to one manufacturer. We’ll quote you the unit that fits your budget and your ductwork, not the unit we get the best kickback on. Call (361) 306-9515 for a written quote.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Denton and the surrounding North Texas communities.