Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Burbank
Heat pump installation in Burbank typically runs $3,500 – $7,500 for a full system, and most jobs are completed in one to two days depending on ductwork condition and access. Burbank’s basin climate means your heat pump runs hard in both heating and cooling modes almost year-round, so getting the sizing right on day one is what separates a system that saves you money from one that fights itself. Our Heat Pump Installation team knows Burbank homes, from the 1950s ranch houses near Chandler Bike Path to the newer builds up in the hills above Brace Canyon Park. Call (361) 306-9515 and we’ll send a tech who can give you a written price before any work starts.
Why Dalton Heating & Air Is Burbank’s Preferred Heat Pump Installation Company
Dalton Heating & Air operates under The Garrison Standard, which has governed how we run every job since 2003. That means a written price before any work begins, a written guarantee on every repair, and a crew that shows up inside the stated window. We’re not a franchise that subcontracts to whoever picks up the phone. Our technicians are background-checked, uniformed, and factory-trained to service nine major residential HVAC brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard.
Burbank homeowners call us because they’ve been burned before. A tech who doesn’t show. A quote that changes at the door. A half-finished install with a crew that disappears. The Garrison Code is specific: arrive inside the stated window, price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. That’s the 365-Day Done Right Promise. If it’s not done right, we make it right.
We answer our phones with a live person 24/7. No voicemail queue, no callback window. When your heat pump fails during a July heat wave in Burbank, you don’t want to leave a message and hope. You want someone who picks up.
Mini Split Installation in Burbank
Mini Split Installation in Burbank is one of the smartest moves for older homes that never had ductwork run to every room, or for additions and garage conversions that sit too far from the main plenum. Burbank’s housing stock includes a lot of single-story homes with limited attic space or flat roofs where running new ducts would mean tearing into ceilings. A ductless mini split solves that. The first sentence of this section names the service and the city: a single-zone mini split install in Burbank runs $3,500 – $7,500 depending on the unit’s capacity, whether the outdoor pad needs leveling, and how far the line set has to travel. It’s a real solution for the unpermitted back-house office or the second-story bedroom that never cools below 78°F in August.
Where Mini Splits Make Sense in Burbank
Homes along Victory Boulevard and the Magnolia Park area often have floor plans where the original HVAC was sized for a smaller footprint and later additions never got proper supply runs. A mini split gives you room-by-room control without re-engineering the whole duct system. We size each indoor head to the room’s actual load, not a rule of thumb.
What to Expect on Install Day
Our tech arrives with the unit, line set, and a written price already agreed on. We mount the indoor head, route the line set through an exterior wall penetration, level and anchor the outdoor condenser, pull a proper vacuum to remove moisture from the lines, and commission the system. You get a walkthrough of the remote and filter access before we leave.
Heat Pump Maintenance in Burbank
Heat Pump Maintenance in Burbank matters more than in other cities because your system doesn’t get a real off-season. A typical tune-up runs $80 – $200, and we recommend it twice a year for Burbank homes because the system alternates between heating and cooling modes with only a short shoulder season in between. Dirt buildup on the outdoor coil, a refrigerant charge that’s drifted, or a reversing valve that’s starting to stick will all show up on a maintenance visit before they become a $650 repair.
What a Tune-Up Includes
We check refrigerant pressures against the manufacturer’s spec, measure temperature drop across the indoor coil, inspect the reversing valve and defrost board, test the crankcase heater, and check static pressure across the blower. Our technicians are not paid on what they sell. You get a written report of what was actually found, with a price in writing for any recommended work.
When to Schedule in Burbank
Book one visit in late winter before the first real warm stretch and one in late fall before nighttime temps drop back into the 40s. That cadence catches the two failure points a Burbank heat pump sees most: a coil that’s been running all summer and a defrost cycle that only gets exercised when nights get cold.
Trusted Brands We Service in Burbank
We install and service Goodman, Rheem, York, and Daikin heat pumps, among the nine major brands our techs are factory-trained on. We keep common parts for these units in local stock, which means less waiting when a Burbank customer needs a capacitor, a reversing valve, or a defrost sensor. Brand matters less than the install quality. A properly sized and charged Goodman will outperform a poorly installed premium unit every time. That’s why we put the load calculation and the commissioning process ahead of the box the unit comes in.
Common Heat Pump Installation Problems We See in Burbank Homes
- Oversizing from the old unit’s tonnage. A lot of Burbank installs start with a tech who just matches whatever tonnage was already there. In this basin, that usually means a system that’s too big for the cooling load, so it short-cycles in winter and never dehumidifies properly in shoulder season. A real Manual J load calculation is the fix.
- Skipped refrigerant charge verification. A new heat pump that’s even slightly under- or over-charged loses SEER2 rating fast. In Burbank’s year-round run pattern, that inefficiency compounds on every single bill.
- Leaky existing ductwork left in place. We see homes in the hills above Kenneth Village where the ducts were installed decades ago and never sealed. The new heat pump fights high static pressure and can’t deliver rated capacity to the rooms. If the ducts are undersized or leaky, the install should include sealing and rebalancing.
- Wrong location for the outdoor unit. Placing a condenser against a west-facing wall with no shade in Burbank means the unit works harder every summer afternoon. We flag that during the site visit and recommend where the unit should actually sit.
Pricing for Heat Pump Installation in Burbank, CA
Here are the numbers, in writing, the same way we’d give them to a Burbank homeowner standing in their living room:
| Service | Typical Burbank Price Range |
|---|---|
| Heat pump installation (full system) | $3,500 – $7,500 |
| Mini split installation (single zone) | $3,500 – $7,500 |
| Heat pump tune-up / maintenance | $80 – $200 |
| AC repair (capacitor, blower motor, refrigerant charge) | $150 – $650 |
What moves the final number: whether existing ductwork can be reused or needs sealing and rebalancing, the unit’s capacity and SEER2 rating, whether the electrical panel has capacity or needs a circuit added, and how far the line set has to run. We give you a written fixed price before any work starts, and that price does not change at the door. Call (361) 306-9515 for a free estimate on a Burbank heat pump install.
We Also Serve Cities Near Burbank
Dalton Heating & Air handles heat pump installation across the San Fernando Valley and surrounding areas. We regularly run crews to Burbank, plus Glendale, West Hollywood, Altadena, and Beverly Hills. Dispatch and scheduling are coordinated from the brand’s Los Angeles office, with crews serving Burbank locally. If you’re in a neighboring city and need a heat pump installed, call the same number: (361) 306-9515.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Burbank
Yes. A Manual J load calculation is not optional on a Burbank install because the city’s basin climate runs a heat pump in both modes hard, and oversizing for cooling destroys heating efficiency. We run the calculation on every install, no exceptions. Call (361) 306-9515 and we’ll walk you through what it showed for your house.
SEER2 is the cooling efficiency rating under the newer testing standard, and a higher number means the unit uses less electricity to produce the same cooling. For a Burbank home running the heat pump year-round, moving from a 14 SEER2 unit to a 17 SEER2 unit can cut the cooling portion of your bill by a noticeable margin. We’ll show you the math on your actual usage pattern during the estimate.
A full heat pump installation in Burbank runs $3,500 – $7,500. The range accounts for unit capacity, SEER2 rating, ductwork condition, electrical panel capacity, and line set distance. We give a written fixed price before any work starts and that price does not change. Free estimates: (361) 306-9515.
If the repair costs more than about 40% of a new unit and the system is over 12 years old, replacement usually wins in Burbank because the year-round runtime means the old unit is costing you money even when it’s working. We’ll give you the repair number and the replacement number side by side, in writing, so you can decide without pressure.
Twice a year. Burbank’s climate doesn’t give your heat pump a real off-season, so we recommend a spring visit before the summer load hits and a fall visit before nights drop into the 40s. Each tune-up runs $80 – $200 and includes a written report of what we found.
Marco Benitez leads the Dalton Heating & Air team serving Burbank. If you’re done with no-shows and door prices, call (361) 306-9515 for a free heat pump installation estimate. We answer the phone with a real person, we give you the price in writing, and we stand behind the work for a full year.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Burbank with written pricing and The Garrison Standard on every job.