Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Beverly Hills
Heat pump installation in Beverly Hills runs $3,500 to $7,500 for a complete system, and most homes are sized at 2.5 to 4 tons. That price includes the equipment, the removal of the old system, the electrical and refrigerant work, and a written price before we start. Beverly Hills sits in a coastal microclimate where summer temperatures run milder than the San Fernando Valley, which means sizing by square footage alone leads to short cycling and higher bills. If you’re seeing repair bills stack up on a system older than 12 years, call us at (361) 306-9515. We’ll give you an honest read on whether a repair or a replacement makes sense for your actual house, not a generic rule of thumb.
Why Dalton Heating & Air Is Beverly Hills’s Preferred Heat Pump Installation Company
Marco Benitez leads our heat pump installation work across Beverly Hills, and he’s the one who makes sure every job meets The Garrison Code: arrive inside the stated window, put the price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. We answer calls with a live person 24/7, so when a Beverly Hills homeowner calls at 6 a.m. or 11 p.m., they’re talking to a human who can dispatch a crew, not a voicemail queue. Our technicians are background-checked, uniformed, and factory-trained to service Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. The Heat Pump Installation team carries the same written pricing and written guarantee on every job, no exceptions.
We’re a Garrison Partners company, operating under The Garrison Standard since 2003. That means the 365-Day Done Right Promise applies to every heat pump install in Beverly Hills: if it’s not done right, we make it right, for a full year. Homeowners in the flats north of Santa Monica Boulevard and up in the hills above Sunset have called us after other crews left duct work unsealed or skipped the refrigerant charge verification. We fix those jobs and then we write the guarantee down and hand it to you.
Heat Pump Service in Beverly Hills
Heat Pump Service in Beverly Hills means diagnosing why a system isn’t heating or cooling correctly, then doing the repair right the first time. We see homes from the 1950s and 1960s along Coldwater Canyon Drive where original duct work was never sealed, and newer construction near the Golden Triangle where the equipment is fine but the static pressure was never checked. A service call costs between $150 and $700 depending on what’s actually wrong, and the price is in writing before we touch anything.
Repair and Diagnosis
When your heat pump short cycles or can’t hold a set temperature, we start with a full diagnostic: refrigerant charge, airflow, electrical connections, and the reversing valve. In Beverly Hills’s mild climate, a system that’s slightly oversized will cycle on and off too fast, which wears out compressors years early.
Refrigerant and Airflow Corrections
A refrigerant recharge, topping off the cooling fluid your system needs to reach set temperature, is a common fix on older R-410A systems. But low refrigerant is a symptom, not the cause. We find the leak before we refill, or you’ll be paying for the same repair again next season.
Heat Pump Replacement in Beverly Hills
Heat Pump Replacement in Beverly Hills should start with a room-by-room load calculation, not a tonnage guess based on what the neighbor has. A three-ton unit on a 2.5-ton house will short cycle all summer and never hit its SEER2 rating. Replacement costs run $3,500 to $7,500 for a full install, and that includes the equipment, the old system removal, any electrical panel work, and a written price before we order anything.
Load Calculation and Sizing
Beverly Hills has a coastal-influenced microclimate where summer design temperatures are milder than the San Fernando Valley a few miles north, so a heat pump sized for a Valley house will short-cycle on mild Beverly Hills days and never hit rated efficiency. We measure every room, window, and duct run before we quote a size.
Duct Sealing and Static Pressure
Homes built before 1970 often have leaky or undersized ducts that undermine a new heat pump’s efficiency. Sealing the duct work and verifying static pressure after install is what makes the SEER2 number on the box show up on your actual bill.
Trusted Brands We Service in Beverly Hills
We install and service Rheem, York, Daikin, and Bryant heat pumps in Beverly Hills, along with five other major brands. Because we stock common parts locally and coordinate dispatch from our Los Angeles office, we can get a replacement compressor or reversing valve to a Beverly Hills home faster than a shop that has to order from the manufacturer every time. If your system is a Daikin but a York makes more sense for your next install, we’ll tell you straight. The goal is the right equipment for your house, not the brand we have sitting in a warehouse.
Common Heat Pump Installation Problems We See in Beverly Hills Homes
- Oversized equipment from neighbor comparisons. We hear it all the time: a homeowner asks us to match the three-ton unit their neighbor installed. If your Beverly Hills home only needs 2.5 tons, that extra half-ton makes the system cycle constantly and wears it out early.
- Skipped static pressure and refrigerant verification. An installer can bolt in a SEER2-rated heat pump and never check the airflow or charge. The equipment will run, but it won’t deliver the efficiency you paid for.
- Ignoring duct work in pre-1970 homes. Older Beverly Hills houses along Coldwater Canyon and in the flats north of Wilshire often have ducts that leak 20 to 30 percent of conditioned air. A new heat pump on leaky ducts is like a new engine in a car with a hole in the gas tank.
- No written price before work starts. We take calls from homeowners who got a verbal estimate and then a bill that was 40 percent higher when the crew left. Our price goes in writing before we order a single part.
Pricing for Heat Pump Installation in Beverly Hills, CA
Heat pump installation in Beverly Hills runs $3,500 to $7,500 for a full system. AC repair in Beverly Hills typically costs $150 to $650, furnace repair $150 to $700, and a tune-up $80 to $200. What moves the install price: the size of the system (2.5 tons vs 4 tons), whether your ducts need sealing or replacement, and whether your electrical panel can handle the new equipment. We give you a written, fixed price before any work starts, and we don’t add overtime charges for evening or weekend calls. Call (361) 306-9515 for a free estimate. The price you see is the price you pay.
| Service | Beverly Hills Price Range |
|---|---|
| AC Repair | $150 – $650 |
| Furnace Repair | $150 – $700 |
| AC Installation | $3,500 – $7,500 |
| Tune-Up | $80 – $200 |
We Also Serve Cities Near Beverly Hills
Dalton Heating & Air handles heat pump installation and repair in Beverly Hills and the surrounding Westside communities: West Hollywood, Culver City, Santa Monica, and Marina del Rey. If you’re just outside Beverly Hills proper, call us and we’ll confirm we can get a crew to you. Most of the Westside is within a short drive of our Los Angeles dispatch office, so response times are consistent across the area.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Beverly Hills
If your heat pump is over 12 years old and the repair will cost more than 30 percent of what a new system would run, replacement usually makes more financial sense. On a $5,000 install, that means a repair over $1,500 is worth questioning. In Beverly Hills, where summer design temperatures are mild, a system that’s been cycling hard for a decade may be oversized and failing early, not just old. Call (361) 306-9515 and we’ll run the numbers on your actual unit before you decide.
Beverly Hills sits in a coastal-influenced microclimate where summer design temperatures are milder than the San Fernando Valley, so any heat pump sized by square footage or by what your neighbor has will short-cycle on mild days and never hit rated efficiency. A room-by-room load calculation is the difference between a system that runs at its SEER2 rating and one that cycles like a car in stop-and-go traffic. It’s the single most important step in a Beverly Hills install.
SEER2 is a rating that measures cooling efficiency under more realistic conditions than the old SEER number. A jump from a 14 SEER2 unit to a 20 SEER2 unit on a typical Beverly Hills home can cut cooling costs by 25 to 30 percent, but only if the system is sized right and the duct work is sealed. If the static pressure is off or the refrigerant charge is wrong, the real-world efficiency drops well below what the rating says. That’s why we verify both after every install.
Most heat pump installations in Beverly Hills are done in one day, though homes with extensive duct sealing or electrical panel upgrades can take two. We schedule a set install date, not a window that stretches across a week. The crew arrives in uniform, does the work, and leaves the site clean. You’ll have heat or cooling the same day we finish.
Yes. Our technicians are factory-trained to service Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. If your Beverly Hills home has a Rheem or a York system that’s still under warranty, we can handle the repair and the paperwork. We don’t push a replacement just because we don’t stock your brand.
Get a Straight Answer on Heat Pump Installation in Beverly Hills
If you’re weighing a repair against a replacement, or you just want a second opinion on a quote someone gave you, call Dalton Heating & Air at (361) 306-9515. Marco Benitez and our team will give you a written price, a set install date, and a straight answer on what your Beverly Hills home actually needs. No pressure, no guesswork, and no surprises when the bill comes.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Beverly Hills since 2003.