Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Cleburne
Furnace repair in Cleburne typically costs between $150 and $700, and most calls are finished in a single visit. If your heat is out on a 22-degree morning near the Johnson County Courthouse square or out toward Nolan River Road, we’ll get a technician to your door fast and put the price in writing before any work starts. Dalton Heating & Air operates under The Garrison Standard, which has governed how we run every job since 2003. That means you get a written quote on every repair, a full-year written guarantee, and a live person on the phone at (361) 306-9515 any hour you call. No voicemail queue, no callback window.
Why Dalton Heating & Air Is Cleburne’s Preferred Furnace Repair Company
Cleburne homeowners call us because we show up inside the stated window and do the job by the book. Our technicians are background-checked and uniformed, so you know who is walking up the driveway before they knock. We’re a Garrison Partners company held to The Garrison Code: arrive on time, price in writing before starting, fix it right, leave the site clean, and stand behind the work for a full year. Every service call includes a written guarantee on the repair itself. If the work doesn’t hold, we return at no charge. That’s not an upgrade or an add-on. It’s the standard.
Our crews are factory-trained to service nine major residential HVAC brands, which matters when a Cleburne home has a 12-year-old Goodman furnace and a newer Daikin heat pump in the same closet. And because dispatch is coordinated from our Dallas-Fort Worth office, we can route a technician to Cleburne quickly without the overhead of a storefront in town. You get the same written price and the same guarantee, whether the call is off Henderson Street or up near the Chisholm Trail Parkway corridor.
Heat Pump Repair in Cleburne
Heat pump repair in Cleburne usually runs $150 to $700, and the most common winter failure we see is a unit that stops heating because the reversing valve sticks or the outdoor coil ices over on a damp, cold night. Many homes here use a heat pump as the primary heat source with electric auxiliary heat strips as backup. When the heat pump can’t keep up, those strips kick in and the electric bill climbs fast. A repair that gets the heat pump running again pays for itself quicker than most homeowners expect.
Cold-Weather Defrost Failures
On Cleburne winter mornings when the temperature hovers just above freezing and the air is wet, heat pumps go into defrost cycles more often. If the defrost sensor or control board fails, the outdoor coil freezes solid and the system locks out. The fix is usually a sensor or board replacement, not a new unit.
Reversing Valve and Refrigerant Issues
A heat pump that blows cold air in heating mode often has a stuck reversing valve or low refrigerant. The refrigerant side of the system needs a trained technician with the right gauges and the EPA certification to handle it. We check the full charge and the valve operation, then write up exactly what failed and what it costs before we touch anything.
Heating Repair in Cleburne
Heating repair in Cleburne covers everything from gas furnaces to heat pump air handlers, and most jobs fall between $150 and $700 depending on the part. The average no-heat call in this part of Johnson County is a failed igniter, a dirty flame sensor, or a blower motor that gave out. These are repairable same-day in nearly every case. Where it gets harder is when the heat exchanger is cracked or the system was never sized right for the ductwork it’s attached to. That’s when an honest repair-versus-replace conversation matters more than a quick part swap.
Igniter and Flame Sensor Failures
On cold, damp Cleburne mornings, hot-surface igniters and flame sensors take a beating. A furnace that clicks on, tries to light, and then shuts down is usually locked out by a dirty flame sensor. A tech can clean it or replace it fast, and the price stays on the low end of the range.
Blower Motor and Airflow Problems
Older Cleburne homes, especially those near downtown with original ductwork, often have undersized return air ducts. That drives static pressure up and forces the blower motor to work harder than the furnace was designed for. The symptom is a furnace that short-cycles or a blower that fails years early. Replacing the motor fixes the immediate problem, but if the ductwork is the root cause, we’ll tell you straight and recommend a load calculation before you spend more money on equipment.
Trusted Brands We Service in Cleburne
Our technicians are factory-trained on nine major brands, and in Cleburne we see a lot of Goodman, Rheem, and York equipment in the field. We carry common parts for those systems on the truck, which means a same-day fix is more likely when your furnace goes down. If you have a Daikin heat pump paired with a gas furnace, we handle that combination too. You don’t need to call a different company because of the badge on the unit. One phone call to (361) 306-9515 covers the repair, the parts, and the warranty work.
Common Furnace Repair Problems We See in Cleburne Homes
- Dirty or failed hot-surface igniters and flame sensors. Cold, damp winter mornings in Cleburne cause these parts to fail more often, especially on furnaces over 10 years old. The symptom is a furnace that tries to light and then shuts down.
- Short-cycling from undersized return ductwork. Older homes near downtown Cleburne and along Nolan River Road often have return ducts too small for the system. The blower motor and heat exchanger wear out faster than the equipment spec expects.
- Heat pump and furnace combinations that were never load-calculated. When the system wasn’t sized for the actual square footage and insulation, the auxiliary heat strips run on nearly every cycle. Cleburne homeowners see it as a furnace that “runs all the time” and a winter electric bill that spikes.
- Stuck gas valves and failed control boards. A gas valve that won’t open or a board that won’t send the signal is common on older equipment. These are repairable, and the part cost determines whether you’re at the low or high end of the $150 – $700 range.
Pricing for Furnace Repair in Cleburne, TX
Most furnace repairs in Cleburne fall between $150 and $700. A dirty flame sensor cleaning or a capacitor replacement lands on the low end. A blower motor, gas valve, or control board replacement runs higher because the part itself costs more. Here’s how the common jobs break down in this market:
| Service | Typical Price Range |
|---|---|
| Furnace Repair | $150 – $700 |
| AC Repair | $150 – $650 |
| Tune-Up | $80 – $200 |
| AC Installation | $3,500 – $7,500 |
Before any work begins, you get the exact price in writing. Not a ballpark, not an estimate that shifts at the door. The written price is part of The Garrison Standard and it applies on every job, no exceptions. Call (361) 306-9515 for a free estimate on your furnace repair in Cleburne.
We ran a furnace repair call off Henderson Street near the Johnson County Courthouse square where the homeowner had no heat on a 22-degree morning. The blower motor was spinning but the igniter wouldn’t light. Our tech traced it to a failed hot-surface igniter plus a weak capacitor on the inducer. We replaced both in under two hours, then checked static pressure and found the return duct undersized for the 3-ton system. We recommended a load calculation before any future equipment change. The homeowner had heat back the same morning and a clear repair-versus-replace baseline on paper.
That kind of finding is common across Cleburne. The housing stock spans older homes near the historic downtown with original ductwork and newer builds on the south side with tighter envelopes. The same furnace complaint, a unit that runs constantly or won’t light, can mean a $180 igniter fix in one house and a much bigger conversation about duct sizing and equipment matching in another. We don’t guess between the two. We test, measure, and write it down.
We Also Serve Cities Near Cleburne
Our Furnace Repair team covers Cleburne and the surrounding Johnson County communities. You’ll see our trucks in Keene, Joshua, Alvarado, and Grandview throughout the week. If you’re one town over and your furnace quits, call the same number: (361) 306-9515. We route a technician to your door with the same written pricing and the same one-year guarantee.
Serving Cleburne, TX - Our Local Coverage Area
We’re based in the Cleburne area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Cleburne
If your repair quote is under $700 and the heat exchanger is intact, repairing is usually the right call in Cleburne. The line to replace comes when the heat exchanger is cracked, the system is over 12 years old, or the ductwork was never sized right for the house. We give you the repair cost, the replacement cost, and the measured airflow numbers so you can decide with real information instead of a sales pitch. Call (361) 306-9515 and we’ll walk you through the math.
A load calculation measures the actual heating and cooling demand of your Cleburne home based on square footage, insulation, window area, and duct capacity. Without one, you might keep repairing a furnace that was never the right size to begin with. With one, you get a clear answer: fix what’s broken now, or stop pouring money into equipment that doesn’t match the house. We run the numbers and put them in writing.
On a cold, damp Cleburne night, a heat pump can stop heating because the outdoor coil iced over and the defrost control failed, or because the reversing valve stuck. The first sign is the system blowing cold air while the thermostat shows heat. Call us at (361) 306-9515 and a technician will diagnose the exact failure and give you a written price for the fix.
SEER2 is the updated efficiency rating for heat pumps and air conditioners, measuring cooling output against energy consumed under more realistic test conditions. A higher SEER2 means lower summer electric bills. On a furnace side, you’ll also see AFUE, which measures how much fuel becomes heat. We translate those numbers into dollars on your actual Cleburne utility bill so you can compare equipment fairly.
A furnace tune-up catches failing igniters, dirty flame sensors, weak capacitors, and cracked heat exchangers before they leave you without heat on a 20-degree Cleburne morning. Most tune-ups run $80 to $200, which is less than an emergency repair call. We check combustion readings, static pressure, and the condition of every safety control, then give you a written report of what we found. Our technicians aren’t paid on what they sell, so the report tells you what actually needs attention and what can wait.
Call Dalton Heating & Air for Furnace Repair in Cleburne
If your furnace is down or running rough, call (361) 306-9515. You’ll reach a live person any hour of the day or night. We’ll schedule a technician for Cleburne, put the price in writing before any work starts, and back the repair with a full-year written guarantee. That’s the Garrison Standard, and it’s been non-negotiable since 2003.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Cleburne and Johnson County with written pricing and a one-year guarantee on every repair.