Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Austin
Furnace repair in Austin typically costs $150 – $700, and most calls get a same-day or next-day visit from our crew. If your heat won’t kick on, don’t wait through another 40-degree night. The Austin team at Dalton Heating & Air is local to Austin, and we answer the phone live at (361) 306-9515. No call center. No voicemail loop. Just a real person who can get a truck rolling to your neighborhood.
Why Dalton Heating & Air Is Austin’s Preferred Furnace Repair Company
Dalton Heating & Air is a Garrison Partners company, in operation since 2003 and held to The Garrison Standard on every job. We serve Austin with a very simple set of rules: the price goes in writing before any work starts, the repair is guaranteed in writing for a full year, and if the repair fails inside that year, we come back at no charge. No exceptions. No fine print.
Austin homeowners tell us the same thing every week: someone quoted one price on the phone, then tried to double it at the door. That does not happen with our Furnace Repair team. The price you approve is the price on the invoice. Every tech who walks through your door is background-checked, uniformed, and factory-trained to service Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. You’ll know exactly who is coming before they arrive.
Marco Benitez runs our Austin operation and holds the crew to The Garrison Code: arrive inside the stated window, price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. That code is why Austin homeowners who try us once tend to call us every season after.
Emergency Furnace Repair in Austin
Emergency Furnace Repair in Austin is exactly what it sounds like: your heat is out, it’s cold, and you need a tech now. Our phones are answered by a live person 24/7. Dispatch and scheduling are coordinated from the brand’s Austin office, so a crew that knows Austin’s streets is usually at your door fast. Emergency furnace repair in Austin runs the same honest range as any other furnace repair: $150 – $700 depending on the part and the failure. There’s no overtime surcharge for night or weekend calls.
No-Heat Calls After Dark
A furnace that dies at 9 p.m. on a January night is a health risk, not an inconvenience. We treat it that way. Call any hour at (361) 306-9515 and a person answers. If the fix is a failed ignitor or a gas valve that won’t open, the tech carries common parts on the truck and can usually finish the repair the same visit.
Dual-Fuel Lockouts and Changeover Failures
In Austin, a huge share of “furnace is dead” emergency calls turn out to be a dual-fuel changeover problem. The heat pump has carried the load all fall, then a cold snap hits, the system tries to switch to gas heat, and a thermostat setting or defrost board keeps the furnace from ever staging on. If your heat pump isn’t keeping up, our Heat Pump Installation in Austin team can also assess whether the unit is sized right for your home. We diagnose it on-site and verify the actual failure before quoting anything.
Furnace Maintenance in Austin
Furnace Maintenance in Austin usually runs $80 – $200 and is the single best way to avoid a no-heat call on the first genuinely cold night of the year. Austin’s climate is lopsided: your system runs AC for seven or eight months, sits mostly idle through a mild fall, then gets asked to produce heat on short notice. That transition is where neglected equipment fails. A maintenance visit catches the dirty capacitor, the weak blower motor, or the heat exchanger issue before it strands you.
Seasonal Tune-Up
We inspect the heat exchanger, test the ignitor, measure static pressure, check gas pressure at the valve, and clean what needs cleaning. You get a written report of what we found and what it cost. Our techs are not paid on commission. They don’t need to sell you parts you don’t need.
Heat Pump and Dual-Fuel Inspection
Because most Austin homes run a heat pump as the primary heat source, we don’t just inspect the furnace. We check the changeover operation, refrigerant charge on the heat pump side, and confirm the thermostat stages the furnace only when it should. That’s the difference between a maintenance visit that finds the real problem and one that just dusts off the burners.
Trusted Brands We Service in Austin
Our Austin techs are factory-trained on nine major residential brands, and we service every one of them: Carrier, Trane, Austin Lennox service, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That matters when you have a Rheem furnace mated to a York heat pump – Austin has a lot of mixed-brand dual-fuel setups – because the tech who shows up actually knows both units. We stock common parts for the brands we see most in Austin homes, which means fewer return trips and faster repairs when your heat is out.
Common Furnace Repair Problems We See in Austin Homes
- Dual-fuel changeover lockouts. The heat pump carries most of Austin’s winter load. When the thermostat or defrost board won’t let the furnace stage on, the whole system looks dead. The fix is usually a recalibration or a board, not a new furnace.
- Strained blower motors and capacitors. Austin systems run hard all summer, then get flipped to heat with no maintenance between seasons. That transition is when capacitors fail and blower motors start drawing high amps. Both are repairable on the spot most of the time.
- Short-cycling from oversized equipment. A lot of Austin homes have units sized for peak August heat. In heating mode, that same oversized equipment short-cycles, which stresses the furnace and hides static pressure problems. A load calculation tells you what’s actually right.
- Heat pump issues that masquerade as furnace failures. Low refrigerant, a dirty condenser coil, or a reversing valve issue on the heat pump side shows up as “my furnace won’t heat” – but the furnace was never the problem. We check both sides before quoting a repair.
Pricing for Furnace Repair in Austin, TX
Here is the straight number, in writing, the same number you’ll see on your invoice:
| Service | Typical Price Range in Austin |
|---|---|
| Furnace Repair | $150 – $700 |
| Furnace Tune-Up / Maintenance | $80 – $200 |
| Emergency Furnace Repair | $150 – $700 |
What moves a furnace repair toward the higher end is the part: a heat exchanger is the most serious job, an ignitor or flame sensor is on the cheaper end. What moves it toward the lower end is simple diagnostics. What does not change the price: the time of day. Our Austin emergency calls are the same rates as daytime work, and every quote is free. Call (361) 306-9515 and we’ll tell you over the phone what a diagnostic visit costs and what the likely fix will run, in plain numbers.
We Also Serve Cities Near Austin
Our Austin crew covers the surrounding metro, too. We run calls to Pflugerville, Cedar Park, Manor, and Round Rock on the same live-dispatch system. If you’re right outside Austin and your heat is out, call (361) 306-9515 – same written pricing, same full-year guarantee, same crew standard. You can also see our Furnace Repair in Austin page for the full local service breakdown.
Serving Austin, TX - Our Local Coverage Area
We’re based in the Austin area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Austin
Nine times out of ten, this is a dual-fuel changeover lockout, not a failed furnace. Austin’s mild winters mean the heat pump does almost all the heating, and the gas furnace only stages on during true cold snaps. When a thermostat setting or defrost board prevents that changeover, the furnace stays off even though it’s fine. The fix is usually a recalibration or a small board repair, not a new furnace. Call (361) 306-9515 and our tech will diagnose both sides of the system before quoting anything.
Use the $5,000 rule but do it honestly. Multiply the repair cost by the age of the furnace in years. If the product is over $5,000, replace. If it’s under, repair. In Austin, furnaces see far less runtime than furnaces in northern climates, so they often outlive their age in years. That means the calculation usually favors repair here, unless the repair touches the heat exchanger. Our techs will show you the math in writing and won’t sell a replacement unless the numbers justify it.
A load calculation measures your actual heating and cooling demand based on square footage, insulation, window area, and orientation. In Austin, a lot of equipment was sized for peak summer tonnage, which leaves the furnace oversized for winter heating. That oversized equipment short-cycles and stresses the heat exchanger. If a replacement is needed, a load calculation on the front end prevents you from buying a furnace that’s too big again. If a repair is all you need, the load calc tells you whether the equipment you have is even worth repairing.
Strictly speaking, SEER2 measures cooling efficiency, not furnace efficiency. But Austin’s dual-fuel systems tie the SEER2-rated heat pump and the furnace into one system. If a repair touches both sides, the efficiency of the heat pump affects how much the furnace ever has to run. On a replacement, matching the SEER2 rating of the heat pump to the furnace’s AFUE rating means the system stages correctly in both seasons. A mismatched pair can leave you with a furnace that cycles too often in winter and a heat pump that strains in summer.
Furnace repair in Austin typically costs $150 – $700, depending on the part and the failure. A flame sensor or ignitor replacement is at the lower end. A heat exchanger repair is at the upper end. Emergency calls are the same rates as daytime work, and every diagnostic visit includes a free written quote before any work begins. Call (361) 306-9515 for an exact quote – estimates are free.
Call Dalton Heating & Air for Furnace Repair in Austin, TX
If your heat is out or your furnace is acting up, call (361) 306-9515 now. You’ll reach a live person, get a straight answer, and if you need a tech, we’ll get one to your Austin home fast. The price goes in writing before any work starts, the repair is guaranteed for a full year, and if it fails in that year, we return at no charge. That’s The Garrison Standard. That’s how we’ve worked since 2003. Call now for a free estimate.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Austin since 2003.