Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Spokane
Heat pump installation in Spokane, WA typically runs $3,500 – $7,500 for a ducted system, and the job usually takes one to two days once equipment is on hand. Most Spokane homeowners call us when their old system fails during a cold snap or a summer heat wave, and we get a real person on the phone 24/7 at (361) 306-9515. We know Spokane’s housing stock: 1950s ranchers on the North Side, turn-of-the-century homes on South Hill, and newer builds in Kendall Yards and Indian Trail all need different approaches to ductwork, electrical capacity, and outdoor unit placement. Our Heat Pump Installation team works throughout Spokane with written pricing before any work starts, so you know the number before we touch a single wire.
Why Dalton Heating & Air Is Spokane’s Preferred Heat Pump Installation Company
Dalton Heating & Air is a Garrison Partners company, held to The Garrison Standard on every job since 2003. The standard is specific: arrive inside the stated window, put the price in writing before starting, do the work by the book, leave the site clean, and stand behind it for a full year. Spokane homeowners tell us the same story again and again: a technician showed up late, quoted one price, then found a reason to charge more at the door. We don’t do that. The price goes on paper first, and if we miss the mark on arrival time, you’ll hear about it from us before you have to chase us.
Every technician who walks into a Spokane home is background-checked and uniformed. You know who is coming before they arrive. We’re factory-trained on nine residential brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That matters in Spokane, where we see a real mix of equipment across older north-side homes and newer developments near Mead. A tech who only knows one brand can’t properly size or commission a retrofit on a mixed system.
Marco Benitez leads the team here. He’s the name behind the guarantee. The 365-Day Done Right Promise means a full year of coverage on every repair and install, not a 30-day window. If something isn’t right, we make it right. If a repair fails inside the guarantee period, we come back at no charge. That’s the promise, in writing, every time.
Response to Spokane neighborhoods like Shadle, Hillyard, and Moran Prairie is same-day in most cases for no-heat calls. Scheduling is coordinated from the brand’s Seattle office, but crews serve Spokane locally. That means the phone gets answered by a live person around the clock, and we dispatch a local tech who knows the area.
Geothermal Heat Pump Installation in Spokane
Geothermal Heat Pump Installation in Spokane is a bigger project than an air-source exchange, and it has to be planned around what’s under your yard. Spokane sits on a mix of basalt, glacial till, and river sediment depending on the neighborhood, and the type of ground loop we can install varies with it. A home in the South Hill area may have shallow bedrock that makes a horizontal loop impractical, while a property near the Spokane River can hit water table issues. The job involves drilling or trenching for ground loops, running them to a heat pump inside the home, and tying the system into your existing ductwork or hydronic distribution. A geothermal install in Spokane generally runs $3,500 – $7,500 for the equipment side, but the ground loop adds substantially more depending on site conditions. We give you a written number for the full scope before any ground is broken.
Spokane homeowners choose geothermal for two reasons: stable COP numbers in single-digit winters and zero outdoor noise. A ground-source system doesn’t care if it’s 5 degrees or 95 degrees outside. The loop temperature stays nearly constant, so the heat pump doesn’t lose capacity the way an air-source unit does on the coldest January nights. That matters here, where winter lows routinely sit in the teens and air-source units run defrost cycles more often. The trade-off is upfront cost and a messier yard during installation. We walk through both sides before you commit.
Vertical Loop Systems for Small Spokane Lots
Plenty of urban Spokane lots don’t have room for a horizontal loop field. Vertical boring goes straight down and needs less surface area. We see vertical loops most often in established neighborhoods like Garland or the Perry District, where setbacks are tight and landscaping is established. The boreholes typically go 150 to 300 feet deep, and the loop gets grouted in place. Cost runs higher than horizontal, but it’s often the only geothermal option on a city-sized parcel.
Open-Loop Systems Near the Aquifer
Some Spokane properties over the Spokane Valley-Rathdrum Prairie Aquifer can support an open-loop system that pulls groundwater, passes it through the heat exchanger, and returns it to the ground. Water quality and well capacity decide whether this works. We test before we quote, and if iron content or flow rate fails, we won’t push an open loop. The wrong call there leads to a fouled exchanger and a bad first winter. Written pricing applies here the same as anywhere else.
Ductless Heat Pump Installation in Spokane
Ductless Heat Pump Installation in Spokane solves a problem we see constantly in older homes here: no ductwork, or ductwork so undersized it strangles a new system. A mini split heat pump puts an outdoor condenser on a pad or wall bracket and pairs it with compact indoor air handlers, one per zone. Installation is measured in days, not weeks, and pricing for a ductless mini split heat pump installation in Spokane runs $3,500 – $7,500 depending on the number of heads and the line-set runs. Homes in Hillyard and East Central, where many structures predate central air, are strong candidates. So are bonus rooms, garages converted to workshops, and the finished basements common off North Ash Street.
Spokane winters push air-source heat pumps hard. A properly sized cold-climate mini split, like the ones in the Trane and Lennox lines we carry, will hold rated output well below freezing. It’s not the same as a 1990s heat pump that gave up around 25 degrees. But the install has to be right: line-set routing, flare connections, evacuation depth, and refrigerant charge all matter. We pull a deep vacuum and weigh the charge to the ounce. That’s the difference between a unit that holds 68 degrees in January and one that runs the backup strips and triples the bill.
Multi-Zone Mini Splits for Spokane’s Split-Level Homes
Spokane has a lot of split-levels and daylight ramblers where one thermostat can’t serve every floor. A multi-zone ductless system puts independent temperature control in each zone: main floor, upstairs bedrooms, and the downstairs family room. We install a single outdoor condenser and run multiple line sets to individual air handlers. Each head gets its own thermostat. Homeowners on Five Mile Prairie and in Country Homes tell us the difference is immediate: the upstairs finally stops feeling like a different season from the main floor.
Single-Head Retrofit for Older Spokane Homes
A single-head mini split in a 900-square-foot bungalow can replace a wall furnace or electric baseboards outright. These older Spokane homes, common in Logan and West Central, don’t have room for ducts, and tearing out plaster to add them isn’t worth the cost. One properly sized head on a south-facing wall handles the whole load. We match the tonnage to a room-by-room calculation, not a rule of thumb. A Goodman or Rheem single-zone unit installed cleanly gives these houses real, efficient heat for a fraction of a retrofit’s disruption.
Trusted Brands We Service in Spokane
We stock common parts locally for Spokane customers, which cuts wait time on repairs and commissioning. Our techs are factory-trained and current on Trane, Lennox, and Goodman heat pump lines, along with Rheem equipment when the job calls for it. What that means for a Spokane homeowner is a faster turnaround when a control board fails or a capacitor goes soft during the first hard freeze. We don’t push one brand across every job. The right equipment depends on your home’s ductwork, electrical panel, and how many square feet you actually heat and cool. We explain the options, put the numbers in writing, and let the house decide.
Common Heat Pump Installation Problems We See in Spokane Homes
- Wrong-tonnage sizing from the previous install. Spokane’s housing stock runs from 1900s foursquares to 1970s split-levels, and a rule-of-thumb “one ton per 500 square feet” guess ignores insulation, window upgrades, and sun exposure. We run a real load calculation instead.
- Refrigerant charge left soft at install. A slightly low charge raises compressor amp draw and kills efficiency without ever triggering a fault code. The first cold snap in Spokane is when weak capacitors and tripped breakers show up. We weigh the charge to manufacturer spec.
- High static pressure from undersized ductwork. Older Spokane homes often have duct runs sized for a gravity furnace, not a heat pump. The blower starves, the coil frosts, and the system never reaches rated SEER2 numbers. We check static pressure before we quote a retrofit.
- Defrost cycle issues in Spokane’s damp winters. Spokane gets wet, slushy cold, not just dry cold. If the defrost thermostat or reversing valve isn’t set right, the outdoor coil ices over and the backup heat runs constantly. We see this most on South Hill homes with long shaded yards.
Pricing for Heat Pump Installation in Spokane, WA
| Service | Typical Range |
|---|---|
| Heat pump installation (ducted) | $3,500 – $7,500 |
| Ductless mini split heat pump installation | $3,500 – $7,500 |
| Heat pump tune-up | $80 – $200 |
| Heat pump repair (capacitor, refrigerant charge, thermostat) | $150 – $650 |
The biggest cost driver on a heat pump install in Spokane is the condition and size of your ductwork. A tight, well-sealed duct system in a newer Indian Trail home supports a straightforward swap. A 1950s rancher off North Ash Street with leaky uninsulated ducts may need duct sealing, modification, or a full ductless conversion to hit the same efficiency numbers. Electrical capacity matters too: older Spokane panels sometimes need a breaker upgrade or a service change before a heat pump goes in. We quote the whole job in writing, including any electrical or ductwork corrections, so the final number matches the estimate. Estimates are free. Call (361) 306-9515 and we’ll send a tech out to measure, calculate, and give you a fixed price.
We Also Serve Cities Near Spokane
Our Spokane crews cover Airway Heights, Mead, Medical Lake, and Cheney for heat pump installation and repair. Each of those communities has its own housing patterns and lot sizes, and the drive time is short enough that we treat them like Spokane neighborhoods for response purposes. Call (361) 306-9515 and a live person answers, day or night.
Serving Spokane, WA - Our Local Coverage Area
We’re based in the Spokane area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Spokane
Yes. A load calculation is the only way to know the correct equipment size for Spokane’s climate. Spokane swings from single digits in winter to the mid-90s in summer, so a heat pump here has to handle both peak heating and peak cooling. A load calculation done in one season alone will usually undersize the unit for the other. We run a room-by-room Manual J calculation on every install, measuring insulation, window area, ceiling height, and orientation. Without it, you’re guessing, and guessing costs you in run-time and comfort. Call (361) 306-9515 for a free estimate that includes the calculation.
SEER2 measures cooling efficiency under new testing standards that more closely match real-world conditions. In Spokane, a higher SEER2 rating on your heat pump means lower summer bills, but it’s only part of the picture. Heating performance matters more here, and that’s measured by HSPF2. A unit with a strong HSPF2 rating will cost less to run during Spokane’s long heating season than one that’s only efficient in cooling. The real bill savings come when the unit is sized right, charged correctly, and matched to clean ductwork. We show you the numbers before you choose equipment. Call (361) 306-9515 for a straight answer on your home.
If your heat pump is over 12 years old and the repair is a compressor or a leaking evaporator coil, replacement usually makes more sense in Spokane. Major repairs on aging equipment run $150 – $650, and you’re still left with an old unit that loses capacity every winter. A new heat pump install at $3,500 – $7,500 resets the clock with a warranty and modern efficiency that actually shows up on your utility bill. But if the unit is under 8 years old and the repair is a capacitor or thermostat, we’ll tell you to fix it, and we’ll guarantee the repair in writing for a full year. No pressure either way. Call (361) 306-9515 and we’ll give you our honest read.
Cold-climate mini splits handle Spokane winters well when they’re sized and installed correctly. These units hold rated output down to single-digit temperatures, which is what Spokane gets on the coldest January nights. The key is proper sizing for the heating load, not just the cooling load, and a clean installation with a deep vacuum and weighed refrigerant charge. We replaced a 2-ton heat pump in a 1950s rancher off North Ash Street where the previous installer had never done a load calculation. The home had new windows, added insulation, and a finished basement, so the old tonnage was wrong in both directions. Our tech ran a room-by-room calculation, corrected the refrigerant charge on the condenser coil, and set the new thermostat calibration to match a two-stage Carrier. The homeowner’s winter run-time dropped and the summer cooling stopped short-cycling. That’s what a proper install does. Call (361) 306-9515 for a quote on your Spokane home.
Same-day in most Spokane neighborhoods, including Shadle, Hillyard, and Moran Prairie. A no-heat call in single-digit weather is a health risk, not a scheduling issue, so we prioritize it. A live person answers the phone 24/7, and a background-checked tech from our Spokane crew heads your way. If the repair can’t hold, we’ll talk replacement options the same day with a written price before any work starts. Call (361) 306-9515 and we’ll get someone moving.
Contact Dalton Heating & Air for Heat Pump Installation in Spokane
If you’re weighing a repair against a replacement, or you want a second opinion on a quote, call (361) 306-9515. We’ll answer in person, schedule a time that works for our Spokane service area, and show up on time with a background-checked technician. The estimate is free, the price is in writing, and the work carries the 365-Day Done Right Promise. Marco Benitez and the team are ready to get your Spokane home comfortable again.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Spokane through The Garrison Standard since 2003.