Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Wimberley
A complete Heat Pump Installation in Wimberley typically runs $3,500 to $7,500, depending on system size, efficiency rating, and whether ductwork needs modification. Most installations take one full day, though homes requiring new ductwork or electrical upgrades may need a second day. Call us at (361) 306-9515 and we’ll give you a written price before any work starts.
Wimberley’s location along the Blanco River and its position in the Hill Country create temperature swings that stress HVAC equipment year-round. Summer afternoons push past 100°F, and winter mornings routinely drop into the 20s. A heat pump installed here has to handle both extremes without forcing you onto expensive auxiliary heat strips. Our crews know the difference between a system sized for San Antonio’s steady heat and one built for Wimberley’s wide thermal range.
We serve homes throughout Wimberley, from the neighborhoods off RR 12 to properties near the Blue Hole and along the Blanco River corridor. Wimberley homeowners call us because they want a crew that shows up inside the stated window, puts the price in writing, and leaves the site clean.
Why Dalton Heating & Air Is Wimberley’s Preferred Heat Pump Installation Company
Dalton Heating & Air operates under The Garrison Standard, a set of rules The Garrison Partners network has enforced since 2003. Every job gets a written price before work begins. Every repair carries a written guarantee for a full year, and if the repair fails within that period, we return at no charge. Marco Benitez leads our team, and every technician who arrives at your door has passed a background check and wears a uniform so you know who’s coming before they ring the bell.
Our Wimberley customers tell us the same things: the old contractor skipped the load calculation, guessed at sizing, and left them with a system that short-cycles or can’t hold temperature on cold mornings. We don’t guess. We measure the house, check the ductwork, and verify the electrical service before recommending equipment. We’re factory-trained on nine major residential brands, including Trane, Lennox, and Goodman, so we’re not locked into selling one manufacturer’s equipment.
Dispatch and scheduling for Wimberley jobs are coordinated from our Dallas-Fort Worth office, but the crews are local. Calls are answered by a live person 24 hours a day, seven days a week. No voicemail queue, no callback window.
Heat Pump Maintenance in Wimberley
Heat Pump Maintenance in Wimberley means keeping the outdoor coil clean enough to shed heat on 100°F afternoons and keeping the defrost cycle working when winter humidity from the Blanco River freezes on the coil. A tune-up in Wimberley runs $80 to $200, and it includes a written report of what we found and what we did.
Coil Cleaning and Airflow Verification
Hill Country dust and hard water combine to coat the condenser coil faster than most Wimberley homeowners expect. When the coil is dirty, head pressure climbs, the compressor works harder, and the heat pump drops into defrost more often than it should. We wash the coil, check airflow across the evaporator, and measure static pressure to confirm the system is moving the right volume of air.
Charge and Defrost Cycle Checks
A heat pump’s refrigerant charge has to be set precisely or efficiency drops and the compressor wears prematurely. We check the charge by subcooling, verify the reversing valve shifts correctly, and confirm the defrost control board cycles properly. For Wimberley homes near the river, this defrost check matters more than it does in drier parts of the Hill Country.
Geothermal Heat Pump Installation in Wimberley
Geothermal Heat Pump Installation in Wimberley uses the stable ground temperature a few feet below the surface to heat and cool your home, and it works especially well here because the Hill Country’s rocky limestone holds consistent temperatures year-round. A geothermal system costs more upfront than an air-source heat pump, typically $3,500 to $7,500 for the heat pump and indoor components, with loop field installation priced by site conditions.
Loop Field Design in Hill Country Soil
Wimberley’s rocky soil varies from limestone shelves to pockets of clay, which affects how a ground loop gets installed. Horizontal loops need enough soil depth, while vertical loops can drill through rock but cost more per foot. We assess the site before recommending a loop configuration so you don’t pay for drilling you don’t need or end up with a loop that can’t exchange heat efficiently.
Dual-Source and Hybrid Options
Some Wimberley homeowners pair a geothermal heat pump with an existing air-source unit for a hybrid system that cuts operating costs without the full loop field expense. The geothermal unit handles the base load, and the air-source system covers peak demand. We’ll run the numbers on what each configuration costs to operate given our local electricity rates and your home’s actual heating and cooling load.
Trusted Brands We Service in Wimberley
We’re factory-trained on Trane, Lennox, Goodman, and Rheem equipment, along with five other major residential lines. That means we’re not pushing one brand because a distributor gives us a better margin. When a Wimberley homeowner needs a replacement heat pump, we match the equipment to the house’s load calculation, ductwork condition, and budget, then install it correctly. We keep common parts stocked for these brands so most repairs in Wimberley don’t wait on a shipment from Houston or Dallas.
Common Heat Pump Installation Problems We See in Wimberley Homes
- Oversized equipment from skipped load calculations. Contractors who guess at sizing install 3-ton units in 1,800-square-foot houses, and the system short-cycles through Wimberley’s mild spring and fall, wearing out the compressor and blower motor years early.
- Dirty condenser coils from Hill Country dust and hard water. Blanco River humidity adds moisture to the limestone dust and coats the coil, raising head pressure and forcing the heat pump into inefficient defrost cycles that spike your electric bill.
- Emergency heat strips running constantly on cold mornings. When the heat pump can’t keep up with a 20°F morning, the auxiliary heat strips kick in and your electric meter spins. A proper load calculation and correctly sized equipment prevent this.
- Improper refrigerant charge from rushed installations. We see heat pumps installed without verifying the charge by subcooling, so the system never hits its efficiency rating. We set the charge precisely and document it in writing.
We replaced a failed Goodman heat pump at a home off RR 12 near the Blue Hole, where the homeowner had been running emergency heat strips for three weeks. After a full load calculation showed the old 3-ton unit was oversized for the 1,800-square-foot house, we installed a properly sized 2.5-ton Carrier variable-speed heat pump with a matched air handler, set the refrigerant charge by subcooling, and verified static pressure across the new evaporator coil was under 0.5 inches of water column.
Pricing for Heat Pump Installation in Wimberley, TX
Here’s what Wimberley homeowners can expect to pay for heat pump work:
| Service | Typical Price Range |
|---|---|
| Heat Pump Installation | $3,500 – $7,500 |
| Heat Pump Repair | $150 – $650 |
| Heat Pump Tune-Up | $80 – $200 |
Installation cost depends on the equipment’s SEER2 rating, whether you need a matched air handler or can reuse existing equipment, and whether ductwork needs modification. A variable-speed system with a higher efficiency rating costs more upfront but reduces the electric bill every month. Every quote includes a written price before work begins, and every repair carries the full-year written guarantee. Call (361) 306-9515 for a free estimate on a heat pump installation in Wimberley.
We Also Serve Cities Near Wimberley
Our technicians regularly run heat pump installations and repairs to Canyon Lake, Dripping Springs, San Marcos, and Buda. If you live outside Wimberley proper but still in the surrounding Hill Country, call (361) 306-9515 and we’ll confirm coverage for your address.
Serving Wimberley, TX - Our Local Coverage Area
We’re based in the Wimberley area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Wimberley
If the compressor or reversing valve has failed and the system is over 12 years old, replacement usually makes more financial sense than repair. A repair under $650 that adds several years of life is worth doing; a repair over half the cost of a new system is not. We’ll give you honest numbers on both options so you can decide without pressure. Call (361) 306-9515 and we’ll walk you through what we find.
Wimberley sits in a band of the Texas Hill Country where summer design temperatures push past 100°F while winter mornings routinely dip into the 20s, so a heat pump here has to be sized for a much wider swing than in San Antonio or Austin. A skipped load calculation means the equipment is either too big and short-cycles, or too small and can’t hold temperature on cold mornings. We measure the house, the windows, the insulation, and the ductwork before we recommend anything.
For Wimberley’s climate, a SEER2 rating of 15 or higher with a variable-speed compressor will handle the wide temperature swings most efficiently. Higher ratings cost more upfront. We’ll show you the payback math based on your actual electric bill and how many hours a year your system runs in cooling versus heating mode. Call (361) 306-9515 for specific equipment recommendations and written pricing.
Yes, though the loop field design depends on what the drilling or trenching actually finds. Limestone shelves require vertical loops, which cost more per foot than horizontal loops in softer soil. We assess the site before quoting so the loop field matches the ground conditions under your specific Wimberley property, not a generic assumption. Call (361) 306-9515 and we’ll schedule a site evaluation.
Twice a year, once before summer and once before winter, catches the seasonal stress points. Wimberley’s Blanco River humidity adds defrost cycles most inland Texas heat pumps rarely see, so the winter check matters as much as the summer one. A tune-up runs $80 to $200 and includes a written report of what we found. Call (361) 306-9515 to schedule.
Contact Dalton Heating & Air for Heat Pump Installation in Wimberley
If you need a heat pump installed, repaired, or maintained in Wimberley, call us at (361) 306-9515. Marco Benitez and the Dalton Heating & Air team will give you a written price before any work starts, a written guarantee on every repair, and a crew that shows up inside the stated window. We serve Wimberley homes from the Blanco River corridor to RR 12 and everywhere in between.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Wimberley since 2003.