Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Reno
Heat pump installation in Reno, TX typically runs $3,500 – $7,500 for a full system, and most jobs are completed in a single day once equipment arrives. We serve every part of Reno, from Highland Park down to the neighborhoods off US-82, with live phone support at (361) 306-9515 whenever you need a straight answer. Our crews know Lamar County’s specific climate demands: summer design temperatures push 98°F while winter lows dip into the mid-20s, so the heat pump you pick has to handle both seasons without guessing. We put the price in writing before any work starts, and we stand behind the installation for a full year.
Why Dalton Heating & Air Is Reno’s Preferred Heat Pump Installation Company
Dalton Heating & Air is a Garrison Partners company, operating since 2003 under The Garrison Standard: arrive inside the stated window, put the price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. Marco Benitez runs our operation, and he holds every tech to that standard on every Reno job. That means no price that shifts at the door and no crew that leaves a mess behind.
Reno homeowners call us because we answer the phone. A real person picks up 24/7, not a voicemail queue and not a callback window. When you call about a heat pump that won’t heat on a January morning or won’t cool on a 99° afternoon, you get someone who can schedule a Reno visit and tell you what the tech will check first. Our technicians are background-checked and uniformed, so you know who’s coming before they arrive.
We stock common replacement parts for the major brands across our local service area, which means faster turnaround for Reno customers who need a capacitor, control board, or matched coil without waiting on a regional warehouse. And every installation includes a written guarantee, not an upgrade and not a handshake.
Heat Pump Replacement in Reno
Heat Pump Replacement in Reno is a decision most homeowners face once their existing system hits 12 – 15 years old, and the call usually comes after a major component failure. The compressor locked up. The reversing valve stopped shifting. The refrigerant charge won’t hold. When that happens, the honest question is whether the repair cost on an aging unit makes sense against the efficiency and reliability of a new system. You’ll want a contractor who gives you a straight repair-versus-replace breakdown, not one who defaults to selling you a new unit. Our Heat Pump Installation team walks through that math with you in plain terms before you spend a dollar.
A full heat pump replacement in Reno typically runs $3,500 – $7,500 depending on tonnage, SEER2 rating, and whether the existing ductwork needs modification. The install includes removing the old condenser and air handler, setting the new equipment, brazing the line set, pulling a proper vacuum, and verifying the refrigerant charge against manufacturer specs. We do not skip the charge verification. A system that cools fine in June but can’t keep up in a January cold snap is usually the result of an unverified charge on a new install.
When Replacement Makes More Sense Than Repair
If your heat pump is past 12 years old and the repair quote lands in the $450 – $650 range for a compressor-related issue, replacement usually wins. The new unit carries a fresh manufacturer warranty and a full-year written guarantee from us. You also move up several SEER2 points, which shows up directly on your summer electric bill.
If the unit is under 8 years old and the failure is a capacitor or control board, repair is almost always the right call. Our repair pricing in Reno runs $150 – $650 depending on the part, and every repair carries its own written guarantee.
What a Proper Replacement Includes
We run a Manual J load calculation before quoting a replacement, not after. That calculation accounts for your home’s square footage, window orientation, insulation levels, and duct static pressure. In Reno, it also has to account for both cooling and heating loads because the design temperatures swing nearly 75 degrees between seasons.
Mini Split Installation in Reno
Mini Split Installation in Reno solves a specific set of problems: a room addition that never got ductwork, a garage or workshop you actually use, or a back bedroom that runs eight degrees warmer than the rest of the house. Instead of extending ducts or overworking your central heat pump, a mini split puts a small indoor air handler on the wall and connects it to a slim outdoor condenser with a refrigerant line set. The price for a ductless mini split install lands inside our $3,500 – $7,500 installation range depending on capacity and number of zones, and a single-zone system for a garage or addition often comes in near the lower end.
Reno homes with older duct systems often have rooms that never got balanced properly. A mini split gives you zone control without cutting into existing ductwork or fighting static pressure problems in an aging plenum. Our techs calculate the heating and cooling load for the specific room, size the unit accordingly, and run the line set so it’s clean and code-compliant.
Single Zone vs. Multi Zone
A single-zone mini split serves one room and is the right move for a garage, workshop, or single addition. A multi-zone system runs two to five indoor units off one outdoor condenser and makes sense when you’re trying to fix comfort in several rooms without replacing the central system. We’ll give you options for both with written pricing before you decide.
Cold-Climate Performance
Because Reno winters dip into the mid-20s, we spec mini splits with low-temperature heating capability and proper base pan heaters when the installer’s guide calls for them. A cheap mini split that loses heating capacity below 30°F won’t help you on the nights Lamar County actually gets cold. We install units rated for the full temperature band.
Trusted Brands We Service in Reno
Our techs are factory-trained on nine major residential HVAC brands, including Trane, Goodman, Rheem, York, and Daikin. That training matters when you’re choosing new equipment in a market where parts availability affects turnaround. We stock common Goodman and Rheem components locally for faster service to Reno customers, and we can order Trane or Daikin equipment with a set install date rather than an open-ended window. Every system we install is covered by the manufacturer’s warranty plus our 365-Day Done Right Promise: if it’s not done right, we make it right, for a full year.
Common Heat Pump Installation Problems We See in Reno Homes
- Oversized equipment from guesswork. Too many Reno installs skip the load calculation and pick tonnage from square footage alone. A half-ton oversized heat pump short-cycles on heating mode in January, never runs long enough to dehumidify in summer, and wears out compressors years early.
- Unverified refrigerant charge on a new install. The system gets brazed in, the vacuum gets pulled, and then the tech just opens the service valves. That works fine in June and falls apart when the outdoor temperature drops. We verify every charge against the manufacturer’s chart before we leave.
- Mismatched coils and ignored static pressure. Replacing the outdoor condenser without matching the indoor evaporator coil or checking blower motor airflow and static pressure kills efficiency and shortens compressor life. It also voids the match rating you thought you were buying.
- Ducted heat pumps put on duct systems that can’t handle them. Higher-efficiency heat pumps move more air, and a return that’s already choked will drop static pressure to the point the system works against itself. We measure static and flag duct issues before installation, not after the system trips on high limit.
Pricing for Heat Pump Installation in Reno, TX
Here are the honest numbers for Reno’s market. A full heat pump installation runs $3,500 – $7,500 depending on tonnage, efficiency rating, and ductwork condition. A repair like a capacitor, refrigerant charge issue, or control board replacement runs $150 – $650. A seasonal tune-up with thermostat calibration runs $80 – $200. These ranges are consistent across our Reno service area, and the price you get on paper before work starts is the price you pay.
| Service | Price Range in Reno |
|---|---|
| Heat pump installation (full system) | $3,500 – $7,500 |
| Heat pump repair (capacitor, charge, controls) | $150 – $650 |
| Seasonal tune-up / thermostat calibration | $80 – $200 |
Every quote is free and in writing. Call (361) 306-9515 for an exact number on your specific home.
We Also Serve Cities Near Reno
Our Reno crews also cover heat pump work in Houston, San Antonio, Dallas, and Fort Worth. If you’re located in one of those areas, the same written pricing, background-checked techs, and 365-Day Done Right Promise apply to every job. We schedule across the wider region daily, so getting on the calendar is usually quick.
Serving Reno, TX - Our Local Coverage Area
We’re based in the Reno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Reno
If the unit is under 8 years old and the failure is a single component like a capacitor or control board, repair almost always wins and costs $150 – $650 in Reno. If the system is past 12 years old and the compressor or reversing valve has failed, replacement usually makes more sense at $3,500 – $7,500 for a new install. We’ll walk you through the math on your specific unit before you spend anything. Call (361) 306-9515 for a free assessment.
A load calculation matters in Reno because Lamar County swings from 98°F summer design temperatures to mid-20s winter lows, and a system sized only for cooling will short-cycle on heat in January. The calculation accounts for square footage, window orientation, insulation, and duct static pressure so the unit runs steady in both seasons instead of fighting itself.
SEER2 is the efficiency rating for cooling output per watt of electricity, and a higher number means lower operating cost for the same cooling work. A jump from a 14 SEER2 system to a 17 SEER2 unit typically cuts cooling energy use by around 15 – 20%, which shows up directly on your June through September bills in Reno. The right size matters more than the rating alone; an oversized 20 SEER2 unit that short-cycles will cost more to run than a properly sized 16 SEER2 system.
Yes, we install single-zone and multi-zone mini splits across Reno, and a garage or room addition install usually lands near the lower end of our $3,500 – $7,500 range. We spec units with low-temperature heating capability because Reno nights drop into the 20s, and a mini split that loses capacity below 30°F won’t keep a garage usable in January. Call (361) 306-9515 for a written quote on your specific space.
We service and install Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard heat pumps throughout Reno. Our techs are factory-trained on all nine brands, and we stock common Goodman and Rheem parts locally for faster turnaround. If you’re deciding between brands, we’ll give you straightforward comparisons on parts availability, warranty terms, and real installed cost, not a sales pitch.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Reno and the surrounding area.