Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Irving
Heat pump installation in Irving typically runs $3,500 to $7,500 for a full system swap, and most jobs are completed in one day once equipment is ordered and the load calculation is done. That price includes the outdoor unit, the indoor air handler, any needed electrical or refrigerant work, and a written quote before we start. We’re not the cheapest crew in Irving, and we don’t try to be. We show up inside the stated window, put the price in writing before any work begins, and stand behind the job for a full year under the 365-Day Done Right Promise. Call (361) 306-9515 and a live person answers, any hour, any day.
Why Dalton Heating & Air Is Irving’s Preferred Heat Pump Installation Company
Dalton Heating & Air has been installing and servicing heat pumps under The Garrison Standard since 2003. That means something specific in Irving: our technicians show up in uniform, background-checked, and trained on nine major residential brands including Trane, Lennox, Goodman, and Rheem. We don’t send a salesperson to size a system by square footage alone. We send a technician who runs a real load calculation on your house, because Irving homes range from 1960s ranch houses near the old Texas Stadium site to newer builds up in Valley Ranch, and they don’t all need the same equipment.
Irving homeowners tell us the same thing again and again: another company quoted a low number over the phone, then changed it at the door. That doesn’t happen with us. The price is in writing before any work starts, every job, without exception. Marco Benitez runs our Irving heat pump installation work, and he holds every crew to The Garrison Code: arrive inside the window, price it in writing, do the job by the book, leave the site clean, and stand behind it for a year. If the repair doesn’t hold, we come back at no charge. Not a discount. No charge.
We also answer the phone. When you call about heat pump installation in Irving, a person picks up, 24/7. No voicemail tree, no “press 2 for service.” If your heat pump dies during a February ice event and you need to talk through repair versus replace, you get a human who can help you think it through.
Geothermal Heat Pump Installation in Irving
Geothermal heat pump installation in Irving is a different animal from air-source work, and the local soil is exactly why. Irving sits on shallow, expansive black clay that shifts with moisture. That clay moves enough to crack foundations, and it also affects how geothermal loops get buried here. In a lot of Dallas-Fort Worth suburbs to the north and west, crews sink deep vertical wells into rock or sandy soil and call it a day. In Irving, deep vertical bores through active clay zones create a higher risk of loop stress when the soil cycles wet-dry-wet through the year. The better install in much of Irving is a horizontal loop field that stays above the active soil zone, buried at a depth where the clay’s movement is less of a threat to the piping. This is a real installation detail that doesn’t apply in Rockwall or Allen or McKinney. It applies here, and we plan for it on every geothermal bid we write in Irving.
What the job involves
A geothermal heat pump install in Irving starts with a site survey to figure out whether your lot can handle horizontal loops or needs a different configuration. Then comes excavation or boring, loop installation, the indoor unit, and duct tie-in. It’s a bigger job than a standard air-source swap, and the equipment cost is higher up front. In Irving, the full geothermal installation ranges from $3,500 to $7,500 depending on loop configuration, lot size, and the home’s heat loss. The payoff is operational: geothermal units move heat instead of creating it, so monthly electric use can drop measurably compared to a conventional heat pump. For an Irving homeowner planning to stay in the house ten years or more, the math often works.
When a geothermal unit makes sense
Geothermal makes the most sense when you have the yard space for horizontal loops, an existing duct system in decent shape, and a long horizon in the home. If your lot is tight, say a smaller lot in the Hospital District or a zero-lot-line build near Las Colinas, a vertical loop might be the only option and the clay movement becomes a bigger planning factor. We’ll tell you straight if the site doesn’t support the loop you want. No one benefits from forcing a loop field into soil that will fight it for 25 years.
Ductless Heat Pump Installation in Irving
Ductless heat pump installation in Irving solves a specific problem: homes in Irving that don’t have ductwork, or rooms that never get comfortable no matter what the central system does. Ductless units, sometimes called mini splits, give you zoned heating and cooling without cutting into the house for duct runs. The outdoor condenser connects to slim indoor wall units through a small refrigerant line, so installation is cleaner and faster than adding a full ducted system. In Irving, a ductless heat pump installation typically falls within the $3,500 to $7,500 range, depending on how many indoor units you’re adding and whether the outdoor unit needs a dedicated circuit.
Where ductless units work best in Irving homes
The classic Irving ductless job is a garage conversion, a sunroom, or an older home along Story Road or in the original neighborhoods near MacArthur where adding ductwork would mean opening walls and ceilings. Ductless lets you condition that space without tearing the house apart. It’s also a strong choice for homeowners who want room-by-room temperature control, especially in two-story Irving houses where the upstairs runs hot from July through September while the downstairs feels fine. You’re not cooling the whole house to make one office comfortable. You cool the office.
What changes the price
Number of indoor heads is the biggest variable. A single-zone setup costs less than a multi-zone system serving three or four rooms. Electrical work matters too: some Irving homes built before 1980 need a panel upgrade before a ductless system can be added, and that’s a real cost we quote in writing before any work starts. We don’t hide it. The price includes the line set, the condensate drain, the wall mount, and full commissioning with refrigerant charge verified to the manufacturer’s spec. If it’s not done right, we make it right under the 365-Day Done Right Promise.
Trusted Brands We Service in Irving
Our Irving heat pump installation crews work on Trane, Lennox, Goodman, and Rheem equipment, along with five more major brands. That means we’re not pushing you into one manufacturer because we get a better margin on it. We size the system to your house and your budget, then install it to factory spec. Because we stock local parts for heat pump repairs in Irving, a failed capacitor or a weak blower motor on one of these brands doesn’t have to mean ordering a part and waiting. We can usually get it same day or next morning. For heat pump installation in Irving, that parts access means less downtime if something gets caught during commissioning.
Common Heat Pump Installation Problems We See in Irving Homes
- Systems sized by old rules of thumb instead of a load calculation. A house in Irving with west-facing windows near the Irving Arts Center needs different capacity math than the same floor plan in Valley Ranch with a different orientation. Oversized heat pumps short-cycle in summer, don’t pull humidity, and leave you cold during a January hard freeze because they never run long enough to heat properly.
- Coils fouling fast from spring pollen and summer dust. Irving sits in a zone where oak and pecan pollen blow for weeks in April and May, and the dry summer months stir up fine dust that settles on outdoor condenser coils. A new heat pump installed without a plan for regular coil cleaning loses real SEER2 performance long before the unit fails. It still runs. It just costs more to run.
- Weak capacitors or blower motors pushing homeowners into replacement too early. We see this pattern in Irving: a heat pump is 8 or 9 years old, a capacitor dies, and another company says it’s time for a whole new system. Often the right fix is a sub-$300 part. If the compressor is strong and the refrigerant charge holds, a repair can buy you several more years. We’ll show you the numbers and let you decide.
- Refrigerant line sets reused from old R-22 systems. Some installers try to save time and money by flushing the old line set instead of replacing it when moving from an older system to a new R-410A or R-454B unit. In Irving homes built before 2010, that old copper often has oil residue and internal scaling that reduces the new system’s efficiency. We replace the line set as part of a proper install, not as an add-on.
Pricing for Heat Pump Installation in Irving, TX
Heat pump installation in Irving runs $3,500 to $7,500 for most full system replacements. A repair falls between $150 and $650 depending on the part. A tune-up is $80 to $200. The installation range moves with equipment size, efficiency rating, and ductwork condition. Here’s the breakdown:
| Service | Typical Cost in Irving |
|---|---|
| Heat Pump Repair | $150 – $650 |
| Heat Pump Installation | $3,500 – $7,500 |
| Heat Pump Tune-Up | $80 – $200 |
The biggest single variable is whether your existing ductwork can move the air the new system needs. In older Irving homes with undersized returns, sometimes part of the install budget goes to duct modifications. We measure and tell you. The price in writing before any work starts includes everything: equipment, refrigerant, line set, electrical, permits, and cleanup. Call (361) 306-9515 for a free estimate. We’ll come measure, do the load calculation, and put a fixed number on paper.
We Also Serve Cities Near Irving
Beyond our Heat Pump Installation work across Irving, our crews cover nearby DFW communities including Dallas, Balch Springs, Hutchins, and Mesquite. If you’re in any of those cities and need a straight answer on heat pump repair or replacement, call (361) 306-9515 and we’ll coordinate a technician who serves your area.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Irving
The honest answer starts with what part failed and what the compressor looks like. A capacitor, contactor, or blower motor failure on an 8-to-10-year-old heat pump in Irving often repairs for $150 to $650 and buys you more years. If the compressor itself is dead, or the system is losing refrigerant through coil leaks and the unit is past 12 years old, replacement usually makes more sense than pouring money into a system that can’t hit its efficiency numbers anyway. We’ll run the numbers with you, not at you, and the repair estimate is in writing before any work starts. Call (361) 306-9515 and we’ll diagnose it straight.
A load calculation uses your home’s actual measurements, window orientation, insulation levels, and air leakage to determine how many BTUs of heating and cooling the house actually needs. In Irving, where houses vary from 1960s brick ranches to 2010s energy-code builds, a rule-of-thumb size guess gets it wrong often. An oversized heat pump in an Irving summer short-cycles, leaving humidity in the air and rooms clammy. An undersized one runs nonstop during a hard freeze and can’t hold set temperature. The load calc changes the equipment size, the duct evaluation, and the real operating cost.
SEER2 is the updated efficiency rating for heat pumps, measuring seasonal cooling output divided by energy used under revised testing conditions that better reflect real ductwork and static pressure. In Irving, where air conditioning runs hard from May through October, a higher SEER2 rating means lower summer electric bills. A 15 SEER2 unit costs less up front than a 20 SEER2 unit but uses measurably more electricity per cooling season. The useful way to think about it in Irving: the difference between a 15 and 20 SEER2 heat pump on an average Irving home typically shows up as $150 to $350 per year in cooling costs, depending on your house and thermostat habits. We’ll show you those numbers before you sign anything.
Ductless mini splits make sense when you’re conditioning a space without ductwork, or when specific rooms in your Irving home refuse to hold temperature. A garage apartment near the University of Dallas, a converted sunroom, or an upstairs bedroom over a hot garage are all typical ductless jobs in Irving. The equipment costs more per ton than a central system but avoids the cost of cutting into walls, and it gives you room-by-room control that a central system can’t match. For the right Irving home, it’s the cleanest answer. For a house with good ducts and a failing central system, a standard ducted heat pump is usually the better dollar.
In Irving, the two things that kill heat pump efficiency fastest are dirty outdoor coils from pollen and dust, and low refrigerant charge from slow leaks. An $80 to $200 tune-up once a year, in spring before cooling season, catches both early. We wash the outdoor coil, check refrigerant pressures, test the capacitor and contactor, measure temperature split across the indoor coil, and give you a written report on what we found. Irving’s pecan and oak pollen comes hard in April and May, and a coil that’s already dirty heading into June works against the unit all summer. Technicians at Dalton are not paid on what they sell, so the tune-up report tells you what’s actually needed, not what pads a commission.
If you’re ready to talk about heat pump installation in Irving, or you just need a second opinion on a repair quote, call (361) 306-9515. A live person answers. We’ll schedule a technician to come measure, diagnose, and put a fixed price in writing. If it’s not done right, we make it right. That’s the whole deal.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Irving, TX.