Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Everman
Heat pump installation in Everman, TX typically costs $3,500 to $7,500 for a full system, depending on tonnage, SEER2 rating, and whether the existing ductwork needs work. That’s the honest range we quote at Dalton Heating & Air, and it’s a written price before any work begins. We’re a Garrison Partners company operating under The Garrison Standard since 2003, which means the crew that shows up in Everman arrives inside the stated window, prices the job in writing, and stands behind the work for a full year. If you’re replacing a heat pump off Everman Parkway or adding a mini split to a 1950s ranch home, call (361) 306-9515 and you’ll get a live person, not a voicemail queue.
Why Dalton Heating & Air Is Everman’s Preferred Heat Pump Installation Company
Everman homeowners have told us the same story for twenty years: a technician no-shows, the price changes at the door, or the install crew leaves refrigerant oil on the porch and a hole in the coil cabinet. The Garrison Code exists to make that stop. Every Dalton job in Everman includes a written price before any work starts, a written guarantee on every repair, and a free return visit if the work doesn’t hold. That’s not a promotion. It’s the operating standard since 2003.
Our techs are background-checked, uniformed, and factory-trained to service nine major residential HVAC brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. When you schedule a heat pump installation in Everman, you know who is coming before they arrive. Marco Benitez, who leads the Dalton Heating & Air crew, doesn’t send out a technician he wouldn’t put in his own house. That’s the standard.
Heat Pump Replacement in Everman
Heat Pump Replacement in Everman starts with one question: is the old system worth repairing, or is it time to stop feeding it money? A full replacement in Everman runs $3,500 to $7,500, and the honest answer depends on compressor condition, refrigerant charge history, and what a Manual J load calculation says the house actually needs. A common mistake we see in Everman’s older homes is oversized tonnage sold on square footage alone. A 1,400-square-foot 1960s brick ranch doesn’t need a 4-ton heat pump, and installing one anyway causes short cycling, high humidity, and premature compressor wear.
Repair Versus Replace: The Load Calculation Test
Before we recommend replacement, we run a load calculation. Not a guess. For Everman homes with mature lot shade and smaller footprints, the number often lands a half-ton lower than the old “rule of thumb” guess. That changes the equipment price, the ductwork plan, and the monthly bill.
What Replacement Never Skips
Every replacement includes a matched indoor coil, verified refrigerant charge after install, and a static pressure reading on the existing ductwork. Skip any of those and the new system chokes. We don’t skip them.
Mini Split Installation in Everman
Mini Split Installation in Everman is the right answer for homes with no existing ductwork, or rooms that never seem to reach set temperature. A ductless heat pump installs on an exterior wall, runs refrigerant lines to an outdoor condenser, and gives you zone control without tearing out ceilings. Cost lands inside the same $3,500 to $7,500 range depending on the number of indoor heads and the SEER2 rating. For an Everman homeowner finishing a garage or adding a room to an older pier-and-beam house, a mini split is usually the cleanest path.
Adding Comfort Without Ductwork
Homes in Everman built before central air was standard often have no return in the back bedrooms, which means those rooms never cool. A dual-zone mini split fixes that without a remodel. We install Rheem, York, Daikin, and Bryant ductless systems, and we stock common parts locally for fast turnaround.
What a Good Mini Split Install Includes
The line set gets a proper flare, the system gets a deep vacuum before refrigerant charge, and the condensate drain gets tested. These are the steps that determine whether the unit runs quietly for ten years or starts leaking in two. The Garrison Standard means we do them on every job, in writing.
Trusted Brands We Service in Everman
Dalton Heating & Air is factory-trained on Rheem, York, Daikin, and Bryant heat pumps, and we carry parts inventory for those brands locally, so a replacement part for an Everman homeowner doesn’t sit in a warehouse for a week. The brand on the cabinet matters less than the install behind it. A properly installed York heat pump with a verified charge and balanced airflow will outperform a premium unit that was thrown in. That said, we’ll quote the unit that fits your load calculation, not the one sitting on the truck.
Common Heat Pump Installation Problems We See in Everman Homes
- Oversized tonnage sold on square footage alone. In Everman’s older, smaller homes this causes short cycling, high humidity, and premature compressor wear. A correct Manual J calculation usually lands a half-ton lower.
- Refrigerant charge never verified after install. A heat pump that ran fine in July struggles to defrost and heat in a February freeze because the charge was wrong from day one. We verify charge on every install, with the manifold gauges, before we leave.
- Ductwork choked with undersized returns. Without a static pressure reading, a new high-SEER2 unit starves for airflow and freezes the evaporator coil in cooling mode. Older Everman homes are especially prone to this because the original returns were sized for heating-only systems.
- Aux heat running constantly in winter. When the heat pump can’t keep up, the electric strip heat kicks in and the bill doubles. The fix is usually sizing and airflow, not a bigger strip heater. We see this regularly in homes off Everman Parkway where the original install was never balanced.
Pricing for Heat Pump Installation in Everman, TX
Here’s what you can expect to pay in Everman, as a line-item range. These are the same ranges we quote over the phone, and they’re the same ranges in the written estimate.
| Service | Price Range |
|---|---|
| Heat Pump Installation (full system) | $3,500 – $7,500 |
| AC Repair (diagnostic + common part) | $150 – $650 |
| Furnace Repair (heat pump aux/emergency heat) | $150 – $700 |
| Tune-Up (pre-season heat pump check) | $80 – $200 |
What shifts the number inside those ranges is tonnage, SEER2 rating, and whether the existing ductwork needs static pressure correction. A 2-ton replacement in a small Everman ranch lands on the lower end. A variable-speed 4-ton with duct modifications lands higher. The estimate is free, it’s written, and the number on the page is the number on the invoice. Call (361) 306-9515 and we’ll put it in writing.
We Also Serve Cities Near Everman
Our Heat Pump Installation team covers the surrounding metro, including Houston, San Antonio, Dallas, and Fort Worth. If you’re in Everman, you’re in the core of our service area, and our crews know Everman well. Dispatch is coordinated from the brand’s Dallas-Fort Worth office, and techs serve Everman locally.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Everman
Yes. Everman sits in a Tarrant County pocket where summers push past 100°F but winters still deliver hard freezes, and the February 2021 event knocked out power for days, so the same heat pump has to prove itself in both modes. An installer who sizes only for cooling leaves you with a system that screams on aux heat in January. A proper Manual J load calculation on an Everman ranch home often lands a half-ton lower than the old rule-of-thumb guess because the smaller square footage and mature lot shade change the math. Call (361) 306-9515 and we’ll run the calculation on your home, not on a guess.
That’s the most common question we get in Everman, and the answer starts with a diagnostic. The heat pump’s compressor may be fine, but if the refrigerant charge was never verified after the original install, the unit can’t move heat in cold weather. A repair on that runs $150 to $650 for a diagnostic and common part. If the compressor is worn or the coil is leaking, replacement makes more sense at $3,500 to $7,500. We’ll show you the numbers for both before you spend a dollar. Call (361) 306-9515 for a written diagnosis.
SEER2 is the updated efficiency rating standard that better reflects real-world ductwork and static pressure conditions. A 15 SEER2 unit installed in Everman with balanced airflow will use less electricity than a 17 SEER2 unit starving for return air. The rating matters less than the install. On a 1950s ranch off Everman Parkway, we measured a blower motor pulling high amps because the original 3-ton unit was oversized and the ductwork was undersized. After installing a correctly sized 2.5-ton Carrier variable-speed heat pump and balancing static pressure, the homeowner’s January electric bill dropped enough that they called back to confirm the meter wasn’t broken. That’s what SEER2 plus a real load calculation does.
Yes, and it’s often the best option for older Everman homes where running ductwork would mean cutting into original ceilings and closets. A ductless mini split installs on an exterior wall with a small line set to an outdoor condenser. No ducts, no demolition. A single-zone unit in a converted garage or a back bedroom addition falls within the $3,500 to $7,500 range depending on capacity. Call (361) 306-9515 and we’ll measure the room and quote it in writing.
If the system is under ten years old, the compressor is quiet, and the refrigerant charge holds, repair is usually the right call at $150 to $650. If the coil is leaking, the compressor is worn, or the system is over fifteen years old and undersized for the home, replacement at $3,500 to $7,500 stops the cycle of false savings. We were called to a 1950s ranch off Everman Parkway where the homeowner’s 3-ton heat pump was short-cycling and the blower motor was pulling high amps. The load calculation showed the house needed 2.5 tons, so we installed a new 2.5-ton Carrier variable-speed heat pump with a matched evaporator coil and a fresh capacitor, then balanced static pressure through the existing ductwork. The aux heat stopped kicking on every cold morning. Call (361) 306-9515 and we’ll give you the same straight answer, in writing, before winter hits.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Everman.