Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Converse
Heat pump installation in Converse, TX typically runs $3,500 to $7,500, and the job takes one to two days once we have your equipment on hand. That price includes a full load calculation, permit handling, and a written quote before any work starts. Converse sits right at the edge of the Balcones Escarpment transition zone, so our Heat Pump Installation team sizes equipment for both 105°F July afternoons and January ice storms that send units into defrost. Marco Benitez runs our Converse crews, and you can reach him directly by calling (361) 306-9515 for a free estimate.
Why Dalton Heating & Air Is Converse’s Preferred Heat Pump Installation Company
Homeowners in Converse have seen enough no-shows and changing prices. That’s exactly what The Garrison Standard, which our shop has operated under since 2003, refuses to allow. Every install starts with a written price before any work begins, and every repair carries a written one-year guarantee. If the work doesn’t hold, we come back free. That’s the 365-Day Done Right Promise, and it applies to heat pump installs in Converse the same as anywhere else we work.
Our techs are background-checked and uniformed, and you’ll know who’s coming before they pull up. We service all nine major residential HVAC brands, including Rheem, Goodman, and Daikin, so we’re not going to push you toward a brand we happen to stock. We’re also not paid on what we sell. When a Converse homeowner near FM 1516 asked us to replace a heat pump that turned out to be repairable for under $300, we told them to keep their money. That’s the standard, not the exception.
Dispatch and scheduling are coordinated from our San Antonio office, and crews run calls into Converse daily. We answer the phone with a live person 24/7, so when your heat pump quits on a 38°F night, you’re not leaving a voicemail and hoping.
Mini Split Installation in Converse
Mini split installation in Converse is the right call when you’ve got a room that never cools, a garage or workshop you’re converting, or an older home without ductwork. The job involves mounting an indoor air handler on the wall, running refrigerant lines and electrical to an outdoor condenser, and setting up a dedicated thermostat or remote. Converse has a lot of 1960s and 1970s ranch homes with room additions that the original HVAC never reached, and a ductless mini split fixes that without tearing into ceilings.
When a Mini Split Beats a Full Ducted System
A mini split makes sense when the load calculation shows a small, isolated area needs targeted heating and cooling. It also works for homeowners who are adding square footage off I-10 near the Converse City Park area and don’t want to oversize an existing system. The equipment cost for mini split installation in Converse falls inside the broader $3,500 to $7,500 range depending on zone count and efficiency rating, though smaller single-zone units sometimes come in lower once we scope the job.
What We Check Before Installing
Before we quote a ductless system, we check the panel capacity, wall space, and line set routing. The outdoor unit needs a level pad and enough clearance for airflow and winter defrost drainage, which matters here because Converse gets hard freezes that can ice up a condenser. We quote all of that in writing before any work begins.
Heat Pump Maintenance in Converse
Heat pump maintenance in Converse should happen twice a year because the system runs both heating and cooling cycles. A spring tune-up preps the cooling side before Converse’s triple-digit stretch, and a fall visit checks the reversing valve and defrost controls before the first hard freeze. A standard tune-up runs $80 to $200, and it includes checking the refrigerant charge, cleaning or replacing the air filter, testing the capacitor, and verifying that the system hits its temperature delta.
What a Tune-Up Actually Prevents
Most Converse heat pump failures we see happen on the hottest afternoon of the year, and the cause is usually a part that gave warning months earlier. A capacitor that tested weak in March becomes a no-cool call in July. Regular maintenance catches that. It also catches refrigerant charge drift, which happens after winter defrost cycles and makes the unit run longer without hitting setpoint.
Written Report on Every Visit
Every maintenance visit ends with a written report of what we found, what we fixed, and what might need attention next season. The price is flat, it’s in writing before we arrive, and our techs aren’t paid to sell you anything. If we find a problem that needs repair, we show you the part, explain what it does, and leave the decision to you.
Trusted Brands We Service in Converse
Dalton Heating & Air performs heat pump installation in Converse with equipment from Goodman, Rheem, York, and Daikin, and our techs are factory-trained on all of them. We stock common replacement parts for Converse customers at local supply houses, which usually means a failed capacitor or blower motor gets fixed same-day rather than waiting on a shipped part. When you call, tell us what’s on your condenser and we’ll arrive already knowing the likely failure points. We don’t push one brand over another; the load calculation and your budget determine what we quote.
Common Heat Pump Installation Problems We See in Converse Homes
- Oversized systems short-cycling on older ranch homes. A lot of Converse homes built before 1990 had a “bigger is better” install with no load calculation. The unit slams on and off, never dehumidifies, and wears out capacitors and blower motors early.
- Refrigerant charge drift after winter defrost cycles. Converse heat pumps swing from 105°F cooling to heating with hard freezes, and that cycling stresses the charge. By the first 100°F week of summer, a drifted charge means the system runs constantly and still won’t hit setpoint.
- Failed capacitors and blower motors from start-stop stress. Heat pumps in Converse run long cooling hours from May through September. Constant cycling kills capacitors, and homeowners often assume it’s the compressor when it’s actually a $30 part.
- Undersized return ducts on added square footage. When a room addition punches past the original return capacity, static pressure climbs and airflow drops. We measure that during the load calculation, and the fix is often simpler and cheaper than replacing the whole system.
Pricing for Heat Pump Installation in Converse, TX
Here’s what heat pump work actually costs in Converse right now:
| Service | Converse Price Range |
|---|---|
| Heat Pump Installation (with load calculation and permit) | $3,500 – $7,500 |
| Heat Pump Maintenance / Tune-Up | $80 – $200 |
| Heat Pump Repair (capacitor, refrigerant charge, blower motor) | $150 – $650 |
The install range is driven by equipment size, efficiency rating, and whether you need ductwork modifications. A 2-ton single-stage unit for a smaller home lands on the lower end. A variable-speed system with a higher SEER2 and zoned controls lands on the upper end. The written estimate breaks all of that down line by line, and the price doesn’t move after you sign. Call (361) 306-9515 for a free estimate at your Converse home.
We Also Serve Cities Near Converse
Dalton Heating & Air runs heat pump installation calls throughout Converse and the surrounding area. If you’re in Universal City, Schertz, Cibolo, or Marion, our crews cover those communities too. Same written pricing, same one-year guarantee, same live person on the phone. If you’re anywhere in the northeast San Antonio metro, call (361) 306-9515 and we’ll get you scheduled.
Serving Converse, TX - Our Local Coverage Area
We’re based in the Converse area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Converse
Heat pump installation in Converse runs $3,500 to $7,500 including the load calculation and permit. Smaller single-stage units sit at the lower end, while variable-speed systems with higher efficiency ratings run higher. Call (361) 306-9515 for an exact written quote.
Yes, when it’s sized correctly. Converse regularly sees 105°F-plus afternoons, and a properly sized heat pump with a clean charge holds setpoint without running nonstop. The key is the load calculation. Oversized units short-cycle, undersized units never catch up, and both waste electricity. We run a Manual J load calculation on every install so the equipment matches the actual heat gain of your home.
For Converse’s climate, aim for SEER2 16 or higher on the cooling side, and check the HSPF2 rating for heating since our winters dip below freezing. Higher efficiency costs more upfront but cuts your July electric bill measurably. We’ll show you the payback on a few equipment options before you decide.
A heat pump in Converse needs maintenance twice a year. Spring prep for the cooling season, fall prep for the heating season and defrost cycle. A tune-up runs $80 to $200 and catches capacitor wear and refrigerant drift before they become a no-cool call in July.
If the repair is under $650 and the system is under 12 years old, repairing usually makes sense. If the compressor or reversing valve has failed, or the unit uses R-22 refrigerant, replacement is often cheaper over the next five years. We’ll show you both numbers and let you decide. Call (361) 306-9515 for an honest assessment, it’s free.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Converse and the surrounding northeast San Antonio area.