Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Arlington
A new heat pump installation in Arlington typically runs $3,500 to $7,500 with a proper load calculation, and most homes we quote land between $4,200 and $5,800 depending on the size of the house and the condition of the existing ductwork. That price includes the equipment, the matched air handler, new refrigerant lines where needed, and the labor to pull the old system out and put the new one in. If you’re replacing an old heat pump or switching from a furnace-and-AC combo, call us at (361) 306-9515 and we’ll put a written price in your hand before any work starts.
We run crews into Arlington every day, from the older ranch-style houses south of I-20 to the newer builds climbing up around Lake Arlington and the neighborhoods off Matlock Road. Our technicians know this housing stock. They know what a 1990s two-story in southeast Arlington needs versus a 2000s single-story near the Parks Mall. That matters because heat pump sizing is not a one-number-fits-all answer here.
Why Dalton Heating & Air Is Arlington’s Preferred Heat Pump Installation Company
When an Arlington homeowner calls us about heat pump installation, the first thing Marco Benitez insists on is a load calculation before any equipment gets recommended. That’s not a sales tactic. It’s the difference between a system that holds 72 degrees in August and one that runs constantly and still leaves the back bedroom warm. Marco Benitez has built the Arlington crew on that discipline, and it’s why our Google reviews from Arlington customers consistently mention the written price and the fact that the tech showed up inside the stated window.
Every Dalton Heating & Air technician is background-checked, uniformed, and factory-trained on nine major residential brands, including Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. When you book heat pump installation in Arlington, you’ll know the technician’s name before they arrive. The price goes in writing before the first tool comes off the truck. And the work carries a written guarantee for a full year under the 365-Day Done Right Promise. If the install isn’t right, we return and make it right at no charge.
We also answer the phone with a live person 24 hours a day, seven days a week. No voicemail queue. No callback window that never comes. If your heat pump fails during a July heat wave in Arlington, you’ll talk to someone on the first ring.
Heat Pump Maintenance in Arlington
Heat Pump Maintenance in Arlington is a twice-yearly job that most homeowners skip until something breaks, and that’s a costly habit in this climate. A heat pump in Arlington pulls double duty, running hard through 100°F-plus summers and still cycling in January when the temperature drops below freezing. That’s a lot of hours on the compressor, the reversing valve, and the blower motor. A tune-up costs $80 to $200, depending on the system and what we find, and it catches the small failures before they turn into $650 repairs or a full replacement.
What We Check on a Heat Pump Tune-Up
We check the refrigerant charge against manufacturer spec, test the capacitor and contactor under load, clean the condenser coil, inspect the reversing valve, and measure static pressure across the blower. On Arlington systems, we pay close attention to the aux heat strips and the thermostat’s lockout settings, because a heat pump that’s dragging the strips into every cold morning is burning money on the electric bill all winter.
Written Report After Every Visit
When our technician leaves your Arlington home, you get a written report of exactly what was measured, what was adjusted, and what’s likely to need attention in the next 12 months. Our technicians are not paid on what they sell. If the system is healthy, we’ll say so. If it’s marginal, you’ll see the numbers.
Geothermal Heat Pump Installation in Arlington
Geothermal Heat Pump Installation in Arlington is a different animal from a standard air-source heat pump, and it makes sense for certain properties here, especially larger lots east of Bowen Road or homes south of Sublett Road where there’s room for a horizontal ground loop. A geothermal system uses the stable temperature of the earth below the frost line to move heat instead of fighting the 105-degree air in July or the cold snap in January. The installed cost runs higher, typically $3,500 to $7,500 for the heat pump side in our service area, but the operating cost drops sharply because the ground never gets as hot or as cold as the air.
Why Arlington Soil Conditions Matter
Arlington sits on a mix of clay-heavy soil and limestone that affects how a ground loop gets installed. A proper geothermal design needs a soil test and a loop field sized to the actual heat load of the house, not a rule of thumb. We run the same Manual J load calculation for geothermal that we run for air-source, and we’ll give you a straight answer on whether your lot can support the loop field before you spend anything.
When Geothermal Makes Sense Here
If you’re building new in Arlington or replacing a system in a house with high ceilings and a lot of west-facing glass, geothermal can cut heating and cooling costs enough to justify the upfront cost over time. But we’ll tell you if it doesn’t. On a standard 1,800-square-foot Arlington ranch with a tight building envelope and good ductwork, a high-efficiency air-source heat pump is usually the smarter first move.
Trusted Brands We Service in Arlington
We install and service Goodman, Rheem, York, and Daikin heat pumps across Arlington, and we stock common capacitors, contactors, blower motors, and reversing valves for these brands in our local trucks. That means faster turnaround when a repair is needed before a full installation. Our technicians are factory-trained on all four brands and eight others, so we’re not guessing at the wiring or the charge weights on your system. When we quote a heat pump installation in Arlington, we’ll lay out the real differences between a Goodman and a Rheem in terms of noise, efficiency, and parts availability here, not just price.
Common Heat Pump Installation Problems We See in Arlington Homes
Arlington’s climate exposes heat pump installation mistakes faster than most markets. Here’s what we regularly find when we’re called in after another install didn’t hold up:
- Oversized units on undersized ductwork. A heat pump that’s too big for the house short-cycles in the summer, which means it never runs long enough to pull moisture out of the air. Arlington’s humidity makes this worse. The house feels clammy even when the thermostat says 72.
- Low refrigerant charge from a rushed install. If the installer didn’t pull a proper vacuum or weigh in the exact charge, the evaporator coil ices up in the summer and the compressor runs hot. We see this on Arlington homes where the original install was done by a low-bid crew that never returned.
- Aux heat strips doing the heating instead of the heat pump. A heat pump that isn’t sized or wired correctly will trip the strips constantly during Arlington cold snaps, and the homeowner won’t know until the electric bill doubles in January. A proper thermostat lockout setting prevents this.
- No load calculation on a replacement. Replacing a 3-ton with a 3-ton because it’s what’s already there ignores the fact that the home may have added a sunroom, new windows, or a second story since the original install. Arlington’s west-facing afternoon sun punishes an undersized heat pump every summer.
Pricing for Heat Pump Installation in Arlington, TX
| Service | Arlington Price Range |
|---|---|
| Heat pump tune-up | $80 – $200 |
| Heat pump repair (capacitor, blower motor, refrigerant charge) | $150 – $650 |
| New heat pump installation (with load calculation) | $3,500 – $7,500 |
What moves the price on a heat pump installation in Arlington is the size of the system, the SEER2 rating you choose, and whether the existing ductwork needs sealing or replacement. A 2-ton Goodman heat pump for a smaller Arlington home will land at the lower end. A 4-ton Rheem or Daikin with a variable-speed air handler and duct repairs will land at the upper end. We’ll give you a written, fixed price before any work begins, and that price includes the load calculation. No add-ons at the door. Call (361) 306-9515 for a free estimate.
We Also Serve Cities Near Arlington
Our Heat Pump Installation crews handle work throughout Arlington and into Mansfield, Kennedale, Burleson, and Cedar Hill. If you’re just outside the Arlington city limits and wondering whether we’ll make the drive, the answer is yes, and the same written pricing and one-year guarantee apply.
Serving Arlington, TX - Our Local Coverage Area
We’re based in the Arlington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Arlington
A heat pump in Arlington that’s more than 12 years old, running on R-22 refrigerant, or needing a compressor replacement is usually a replacement candidate, not a repair. If the repair is under $650 and the system is otherwise healthy, we’ll fix it and guarantee the repair in writing for a full year. If the repair is approaching half the cost of a new system, the math points to replacement. Call (361) 306-9515 and we’ll give you an honest read with the numbers in front of you.
A Manual J load calculation accounts for your house’s actual square footage, ceiling height, window area and orientation, insulation levels, and the number of people living there. In Arlington, that calculation is the difference between a 3-ton and a 3.5-ton unit, which determines whether the house holds temperature in both a July heat wave and a hard January freeze. Every Dalton Heating & Air installation quote includes a load calculation as standard. If a contractor quotes you a system without one, you’re getting a guess.
A new heat pump installation in Arlington runs $3,500 to $7,500 depending on system size, SEER2 rating, and ductwork condition. A heat pump tune-up runs $80 to $200, and a typical repair runs $150 to $650. We’ll put the exact price in writing before any work begins.
Yes. SEER2 is the new federal efficiency standard that more accurately reflects real-world performance in hot climates like Arlington’s. Going from a 14 SEER2 to a 17 SEER2 heat pump on a 2,000-square-foot Arlington home can cut cooling-season electric use by roughly 15 to 20 percent. The tradeoff is a higher upfront cost, so we’ll show you the payback math for your specific house and let you decide.
Twice a year, once in spring before the cooling season and once in fall before the winter cold snaps. Arlington’s heat pumps work year-round, and the wear accumulates fast. A tune-up costs $80 to $200 and includes a written report of everything we found. Call (361) 306-9515 to book yours.
If you’re ready to replace a failing heat pump or just want a straight answer on whether repair or replacement makes more sense, call Dalton Heating & Air at (361) 306-9515. We serve Arlington with written pricing, same-window arrival, and a full-year guarantee on every installation.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Arlington, TX.