Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterHow Much Does Furnace Replacement Cost in Los Angeles?
Furnace replacement in Los Angeles typically runs $4,200 to $9,800 installed, with most single-family homes landing between $5,400 and $7,200 for a standard 80,000 BTU gas furnace. That figure covers the unit, labor, permit, haul-away of the old equipment, and a new thermostat in most cases. If you’re replacing an older system in a 1,500 to 2,200 square-foot home, expect to sit near the middle of that range unless ductwork or venting needs work.
We’re Dalton Heating & Air, a Garrison Partners company serving Los Angeles since 2003, and we put every price in writing before any work starts. Call (361) 306-9515 for a free estimate.
Furnace Replacement Cost Breakdown (2026)
Here’s how the money actually breaks down on a Los Angeles furnace replacement. These are real install ranges for our market, not national averages.
| Line Item | Typical Range (Installed) |
|---|---|
| Standard 80% AFUE gas furnace (80,000 BTU) | $4,200 – $6,400 |
| High-efficiency 96%+ AFUE condensing furnace | $6,800 – $9,800 |
| Labor and installation | Included above |
| Permit and inspection (LADBS) | $180 – $450 |
| New thermostat (standard programmable) | $150 – $400 |
| Ductwork repair or partial replacement | $600 – $3,200 |
| Flue or venting upgrade (required with high-efficiency) | $350 – $1,100 |
| Old equipment haul-away and disposal | $75 – $200 |
| Auxiliary work (electrical, gas line resizing) | $200 – $900 |
What pushes you toward the top of the range? High-efficiency condensing units cost more up front because they require PVC venting and a condensate drain rather than the metal flue your old furnace likely uses. Ductwork in older Los Angeles homes, particularly pre-1970 builds in Mid-City and Highland Park, is often undersized or leaking, and sealing or replacing runs adds cost. What pulls the number down? A simple like-for-like swap of a standard 80% furnace in a home with clean, adequate ductwork can stay close to the $4,200 floor.
For a focused look at the replacement side specifically, see our Furnace Replacement in Los Angeles page.
What Affects Furnace Replacement Pricing in Los Angeles
- Furnace efficiency rating (AFUE). An 80% AFUE furnace vents through a metal flue; a 96%+ condensing unit vents through PVC and recovers more heat. The efficiency jump adds roughly $2,000 to $3,000 installed, but it can cut your gas bill noticeably over a decade. AFUE stands for Annual Fuel Utilization Efficiency, the percentage of fuel that becomes usable heat.
- Home size and required BTU output. A 1,200 square-foot bungalow in Boyle Heights needs a smaller furnace than a 3,000 square-foot home in Encino. Bigger equipment costs more, and the load calculation (a Manual J) determines what you actually need so you don’t oversize the unit.
- Ductwork condition. Los Angeles has a lot of older housing stock with original ductwork. We regularly find disconnected runs in raised-foundation homes and crushed flex duct in attics, especially in San Fernando Valley homes built before 1980. Duct sealing or replacement is the single biggest swing factor in most replacement quotes we write.
- Venting requirements. Switching from an 80% to a 96% furnace means new PVC intake and exhaust runs, which may need to route through a wall or roof. On homes in dense neighborhoods like Koreatown, termination clearance from windows and property lines can complicate the routing and add labor.
- Permits and local code. A furnace replacement in the City of Los Angeles requires a mechanical permit through LADBS. Some cities within the county, including Santa Monica and Pasadena, have their own permitting and seismic-bracing requirements. We handle the paperwork, but permit fees are a real line item.
- Season and scheduling. Replacement demand spikes in November and December when the first cold snap hits. Booking in September or October usually means more scheduling flexibility and, in some cases, promotional pricing on the equipment itself.
How to Save on Furnace Replacement
You don’t need to chase the lowest bid. A cheap install that skips the load calculation or reuses failing ductwork costs more in the long run. Here’s what actually lowers your out-the-door number:
- Get a written, line-item quote. Every Dalton estimate spells out equipment, labor, permit, and any ductwork separately. When one bid is thousands below another, you can see exactly what got left out.
- Ask whether you need high-efficiency. A 96% furnace saves gas, but if you plan to move in three years or your home is well-insulated, a quality 80% unit is a sound financial call.
- Bundle duct sealing. If ducts need work anyway, doing it during the replacement saves the second mobilization charge you’d pay to have a crew come back later.
- Check for utility rebates. SoCalGas periodically offers rebates on qualifying high-efficiency furnaces. We’ll flag what’s currently available for your address during the estimate.
- Book before the rush. Scheduling in early fall keeps you out of the December backlog and often gets you a better equipment price.
Estimates are free, and the price you get in writing is the price you pay. Call (361) 306-9515 to schedule one.
How Furnace Replacement Works: Step by Step
- In-home assessment and load calculation. We measure your home, check insulation and windows, and run a Manual J load calculation to size the furnace correctly. Oversized furnaces short-cycle and wear out faster; undersized ones never keep up on a cold night.
- Written estimate. You get a line-item price before we start anything: equipment, labor, permit, ductwork, thermostat, haul-away. No surprises at the door.
- Permit and equipment order. We pull the LADBS mechanical permit and order the furnace. Because we’re factory-trained on Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard, we can match a unit to your budget and your existing setup.
- Removal and installation day. Our background-checked, uniformed technicians arrive inside the stated window, remove the old furnace, set the new one, connect gas and electrical, and run the new venting if required. Most replacements are done in one day.
- Commissioning and walkthrough. We test the unit, check gas pressure and temperature rise, verify the thermostat, and walk you through the system before we leave. The site gets left clean.
- Guarantee and follow-up. Every job carries a written guarantee plus our 365-Day Done Right Promise. If the installation fails within that year, we come back at no charge.
FAQs – Furnace Replacement Cost
Is it cheaper to repair or replace my furnace in Los Angeles?
If your furnace is under 12 years old and the repair is under $500, repair usually wins. Once you’re past 15 years or facing a repair above $800, replacement is the better financial call, since you’re likely to face another failure within a year or two. General furnace repair in Los Angeles runs $175 to $825 depending on the part, so a single major repair can approach a meaningful fraction of a new install. Call (361) 306-9515 for a free estimate and we’ll give you the honest math on your specific unit.
How long does a furnace replacement take in Los Angeles?
Most standard replacements take one day, typically six to eight hours. If the job includes ductwork replacement or a high-efficiency conversion that needs new PVC venting routed to an exterior wall, plan on two days. We tell you the schedule up front and arrive inside the stated window.
How much does a high-efficiency furnace cost in Los Angeles?
A 96%+ AFUE condensing furnace installed in Los Angeles runs $6,800 to $9,800, including the new venting and condensate drain that high-efficiency units require. The efficiency gain lowers your gas usage, but the higher install cost means the payback depends on how much you heat and how long you stay in the home. We’ll run the numbers for you during the estimate.
Do I need a permit to replace my furnace in Los Angeles?
Yes. The City of Los Angeles requires a mechanical permit through LADBS for a furnace replacement, and the fee usually runs $180 to $450 depending on valuation. Pulling the permit matters for resale and for your homeowner’s insurance. We handle it as part of the job and include it in your written price.
What furnace brands do you install in Los Angeles?
We’re factory-trained on nine major residential brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That range lets us match equipment to your budget and your existing ductwork rather than pushing one brand. Call (361) 306-9515 and we’ll recommend the right unit for your home.
Why Homeowners Call Dalton Heating & Air
We’ve operated in Los Angeles since 2003 as part of Garrison Partners, held to The Garrison Standard on every job. That means the price is in writing before we start, the technicians are background-checked and uniformed, and every job is backed by the 365-Day Done Right Promise. If a repair fails within the guarantee period, we return at no charge. Calls are answered by a live person 24 hours a day, so you’re never stuck in a voicemail queue.
Ready to get a written price on your furnace replacement? Call (361) 306-9515 for a free estimate, or start from our home page to see everything we service across Los Angeles.
Pricing reflects the Los Angeles market as of 2026. Dalton Heating & Air offers free estimates – call (361) 306-9515.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Los Angeles since 2003.
What Our Customers Say
"Coil cleaning and a refrigerant check before summer. AC has never been this cold."
- Marty D."Good communication, tidy, and disciplined work. Taped off the floor and wiped the unit down."
- Karen J."Installed a heat pump to replace an old oil furnace. Three clear quotes and the install crew was tidy."
- Cheryl B.