Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Fast, Reliable Furnace Repair Across Rendon
When your furnace quits on a cold Rendon night, you need a straight answer and a fast fix. Most furnace repairs in Rendon run $150 – $700 depending on the part, and our techs arrive in a marked van, background-checked and uniformed, with the repair price in writing before any work starts. We answer the phone at (361) 306-9515 with a live person, 24/7. No voicemail queue. No callback window. If you’re off FM 1187 or down toward Rendon Retreat, we know the streets, the soil, and the systems sitting in these houses.
Why Dalton Heating & Air Is Rendon’s Preferred Furnace Repair Company
Rendon homeowners call us because we show up inside the window and put the price in writing before touching the unit. That’s The Garrison Standard, and it’s been the operating rule across our Furnace Repair network since 2003. Marco Benitez leads our team, and every tech carries factory training across nine major brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. We don’t guess. We test, show you what we found, and quote the fix with a written one-year guarantee on every repair. If the work fails inside that year, we return at no charge. That’s the 365-Day Done Right Promise, and it’s not an upgrade. It’s standard.
We serve Rendon with local crews, not a rotating cast of subcontractors. Dispatch runs from our Dallas-Fort Worth office, but the tech at your door knows Rendon’s housing stock: brick ranch homes off Rendon Road, newer builds near the Retreat, and pier-and-beam houses where ductwork reacts to the soil underneath. That local knowledge changes how we diagnose.
Boiler Repair in Rendon
Boiler Repair in Rendon comes up more often than people expect, especially in older homes and additions where hydronic heat was the original system. A boiler that bangs, leaks, or won’t hold pressure needs a tech who understands circulator pumps, expansion tanks, and aquastats, not just forced-air furnaces. Most boiler repairs in Rendon fall between $150 and $700, with circulator pump and pressure valve replacements at the higher end and control or thermocouple fixes lower.
Circulator Pump and Zone Valve Work
When one zone stays cold while another heats, the problem is usually a stuck zone valve or a failing circulator pump. We check both, replace only what’s failed, and leave you with a written price before parts come off the truck.
Boiler Pressure and Expansion Tank Issues
Rendon’s clay-heavy soil shifts, and pier-and-beam homes here can settle unevenly. That doesn’t directly break a boiler, but it can stress the piping runs. Low pressure, gurgling, or a relief valve that drips usually traces back to a waterlogged expansion tank or a fill valve that’s not seating. Both are straightforward repairs.
Gas Furnace Repair in Rendon
Gas Furnace Repair in Rendon is our bread and butter. These systems run hard from late October through March, and when one quits, it’s usually a failed ignitor, a dirty flame sensor, a gas valve that won’t open, or a blower motor that’s given up. Repairs in Rendon typically cost $150 – $700. A flame sensor cleaning or ignitor replacement sits at the low end. A gas valve or blower motor replacement lands higher.
Ignitor and Flame Sensor Failures
The ignitor glows, the gas valve opens, the burners light. When that sequence fails, it’s often the ignitor or the flame sensor. We replace ignitors in under an hour on most units, and we check the flame sensor’s microamp reading before condemning anything.
Gas Valve and Control Board Repairs
A gas valve that won’t open or a control board that won’t send the signal stops the furnace cold. We test voltage at the valve, verify the board’s output, and never swap a part on a guess. You get the written price first, every time.
Trusted Brands We Service in Rendon
We’re factory-trained to service Goodman, Rheem, York, Daikin, and five other major brands. That matters in Rendon because these houses have a mix: Goodman and York in newer construction, Rheem and Bryant in the 1990s-era Ranchette Estates and Rendon Ranch, and the occasional Daikin in recent retrofits. We stock common ignitors, flame sensors, capacitors, and pressure switches in our local trucks, so a single-visit repair is realistic for most failures. If it’s a less common part, we tell you the lead time before we quote anything.
Common Furnace Repair Problems We See in Rendon Homes
- Short-cycling from high static pressure. Rendon sits where Blackland Prairie clay meets the sandy Cross Timbers soils, and slab or pier-and-beam movement here can rack supply and return ducts out of alignment. That drives static pressure up and triggers high-limit trips, especially on Goodman and York furnaces with single-stage blowers. We measure static pressure before replacing parts on a short-cycling furnace.
- Cracked heat exchangers that look fine from the outside. Aging Bryant and Lennox units in Rendon’s 25-to-35-year-old homes often pass a visual check but fail under combustion analysis. We test flue gases and inspect the exchanger with a camera, because a crack that leaks carbon monoxide is not a repair-and-pray situation.
- Blower motor and capacitor failures after hard no-heat stretches. Rheem and Trane furnaces with permanent split capacitor motors wear out the capacitor first, then the motor. Homeowners sometimes mistake the symptoms, humming or no airflow, for a thermostat problem. We test the capacitor, motor windings, and thermostat signal in one pass.
- Undersized return ducts from original construction. Some older Rendon homes were built with one central return and undersized trunk lines that were marginal when the house was new. Add a decade of filter changes, a few closed vents, and some soil movement, and the furnace struggles. We read static pressure and tell you whether the furnace is failing or the ductwork is.
Pricing for Furnace Repair in Rendon, TX
Here are the numbers we quote in Rendon, in writing, before any work starts:
| Service | Typical Cost in Rendon |
|---|---|
| Furnace Repair (ignitor, flame sensor, capacitor, pressure switch) | $150 – $700 |
| Furnace Tune-Up (inspection, cleaning, combustion test) | $80 – $200 |
A blower motor or gas valve replacement pushes toward the upper end of the repair range. An ignitor or flame sensor cleaning lands at the bottom. You get the exact price before we open the panel, and that price doesn’t move. Estimates are free. Call (361) 306-9515 and we’ll walk you through what we found and what it costs.
We Also Serve Cities Near Rendon
Our techs run calls across the metro. In addition to Furnace Repair in Rendon, we serve Houston, San Antonio, Dallas, and Fort Worth, with the same written-price standard and the same one-year written guarantee on every repair. If you know someone just outside Rendon with a furnace down, give them our number.
Serving Rendon, TX - Our Local Coverage Area
We’re based in the Rendon area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Rendon
The decision in Rendon often turns on duct static pressure and soil movement, not just the heat exchanger. If a furnace is 18-plus years old, needs a heat exchanger or a major component, and the ductwork is already compromised by clay-and-sand soil shifting, our Heat Pump Installation in Rendon or a full replacement may cost less over five years than repeated repairs. We run the numbers honestly: a $700 repair on an 8-year-old furnace makes sense; a $2,500 repair on a 22-year-old unit with undersized returns usually doesn’t. Call (361) 306-9515 and we’ll give you the straight answer in writing.
Short-cycling on mild nights usually points to a furnace that’s oversized for the heat load or a return duct that’s undersized or pinched, and Rendon’s soil movement makes the duct problem common. On cold nights the longer run time masks the issue. We test static pressure and compare your system’s BTU output to the house’s actual load before recommending a repair.
SEER2 is a cooling efficiency standard, but the questions come up during furnace replacement discussions because homeowners in Rendon often replace the furnace and the outdoor unit together. When we quote a repair on an old furnace, part of the question is whether the air conditioner side of the system is also nearing the end. We’ll tell you what the current SEER2 rating means for your summer bills and whether a new system qualifies for a rebate.
Yes. We repair boilers and gas furnaces across Rendon, including hydronic systems in older homes and additions off FM 1187 and Rendon Road. Circulator pumps, zone valves, expansion tanks, pressure controls, and gas valves are all in our wheelhouse, and the repair falls within the same $150 – $700 range as furnace work.
Most Rendon furnace repairs run $150 – $700. An ignitor replacement or flame sensor cleaning is typically $150 – $300. A blower motor or gas valve lands between $400 and $700. The written price you get before we start is the price you pay. Nothing added at the door. Call (361) 306-9515 for an exact quote, free.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Rendon and the surrounding metro since 2003.







Before
After
Before
After
Before
After