Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Kenmore
Furnace repair in Kenmore, WA typically runs $150 – $700 depending on the part, and most no-heat calls can be diagnosed and fixed the same day we arrive. We work in Kenmore every week, from the ramblers off 68th Ave NE to the newer builds near the former Kenmore Village site. That matters because a furnace problem in a 1962 rancher with original ductwork behaves differently than one in a 2005 two-story. Call (361) 306-9515 for a written price before any work starts.
Why Dalton Heating & Air Is Kenmore’s Preferred Furnace Repair Company
Kenmore homeowners call us when they’ve had enough of crews that show up late, quote one number on the phone, and hand over a different invoice at the door. Every Furnace Repair job we do starts with a written price, agreed to before our tech touches a screwdriver. That’s not a promotion. It’s The Garrison Standard, the operating code we’ve been held to since 2003.
Marco Benitez leads the team, and he’s built the schedule around a simple promise: a live person answers the phone 24/7, the tech arrives inside the appointment window, and the work comes with a written guarantee for a full year. If a repair fails in that time, we return at no charge. That second visit is free, not discounted.
We carry common parts for Carrier, Trane, Lennox, and Goodman furnaces in our service vehicles, which means a single-trip fix for most Kenmore repair calls. No ordering a control board from a warehouse two states away and making you wait three days in a cold house.
Emergency Furnace Repair in Kenmore
Emergency Furnace Repair in Kenmore means a no-heat call during a cold snap, when the temperature in your living room drops below 55°F and you can’t wait until Tuesday. We keep same-day slots open for these calls and dispatch techs to Kenmore throughout the day. The cost for emergency furnace work in Kenmore runs the same range as standard repair: $150 – $700, with the price in writing before we start. There’s no after-hours premium and no “emergency surcharge” added on top.
No-Heat Repairs the Same Day You Call
A furnace that won’t fire is a genuine health risk in a Pacific Northwest winter, especially in older Kenmore homes with single-pane windows. We treat these calls as priority and typically have a tech in Kenmore within hours, not days.
Ignition and Flame-Sensor Failures
Kenmore furnaces that short-cycle on oversized, leaky ductwork tend to foul flame sensors faster than they should. The symptom looks scary: the burner lights for a few seconds, then shuts off. In most cases it’s a dirty flame sensor we can clean and test in under an hour, not a failed control board.
Furnace Maintenance in Kenmore
Furnace Maintenance in Kenmore should happen every fall, before the first sustained cold stretch. A tune-up runs $80 – $200 and includes an inspection of the heat exchanger, blower motor, ignition system, and gas pressure. The point isn’t just catching small problems before they become no-heat calls in January. It’s keeping a furnace running at the combustion efficiency it had when it was installed.
Written Report After Every Tune-Up
After every maintenance visit, you get a written report detailing what was tested, what was found, and what we recommend. Our techs are not paid on what they sell. If the report says the heat exchanger is sound, you can believe it. If it says there’s a crack, we’ll show you the photo.
Filter and Static Pressure Checks
Kenmore’s older homes often have undersized return ducts, and a dirty filter compounds that problem fast. We measure static pressure during maintenance because high static pressure is what kills blower motors and trips high-limit switches. It’s a two-minute check that prevents a $400+ blower motor replacement later.
Trusted Brands We Service in Kenmore
Our techs are factory-trained to service nine major residential furnace brands, including Rheem, York, and Bryant furnaces common in Kenmore homes. We keep replacement parts for these systems on the truck whenever possible, which shortens the time between diagnosis and a fixed furnace. Whether your equipment is a 25-year-old Rheem that’s been running since the Clinton administration or a Bryant installed last decade, we service it the same way: written price, written guarantee, done.
Common Furnace Repair Problems We See in Kenmore Homes
- Blower motor capacitor failure in older ramblers: The furnace runs but the blower doesn’t spin, so the burners overheat and the high-limit switch trips. Homeowners often replace the thermostat first, but the real culprit is a $30-ish capacitor and restricted airflow from a clogged filter or undersized return duct.
- Fouled flame sensors from short-cycling: Furnaces paired with oversized, leaky ductwork in 1950s and 60s Kenmore homes cycle constantly, which accelerates carbon buildup on the flame sensor. The furnace lights, runs for ten seconds, then shuts off. Cleaning the sensor usually fixes it.
- Cracked heat exchangers in 20-plus-year-old units: A furnace can still produce heat with a small crack in the exchanger, but it’s unsafe. We find these most often in equipment past the two-decade mark in Kenmore’s waterfront-adjacent homes, where marine air adds corrosion stress. Any heater of that age should get an exchanger inspection every year.
- Tripped high-limit switches from static pressure problems: Older Kenmore homes with original ductwork frequently run high static pressure, especially with a dirty filter. The furnace overheats, the limit switch trips, and the system cycles off. Replacing the limit switch without addressing the airflow problem just repeats the failure.
Pricing for Furnace Repair in Kenmore, WA
Most furnace repairs in Kenmore land between $150 and $700. Here’s the breakdown:
| Service | Typical Kenmore Price Range |
|---|---|
| Emergency Furnace Repair | $150 – $700 |
| Furnace Maintenance / Tune-Up | $80 – $200 |
What moves the price is the part, not the neighborhood. A flame sensor cleaning sits at the low end. A blower motor replacement runs higher. A cracked heat exchanger on an old furnace usually means the repair isn’t worth it, and we’ll tell you that plainly. Call (361) 306-9515 for a free estimate with the price in writing before any work begins.
Kenmore’s Housing Stock and What It Means for Your Furnace
Kenmore is a mix of 1950s and 60s ramblers near Lake Washington and newer construction around the former Kenmore Village site. That split matters for furnace repair and replacement decisions. The older homes often have undersized or unsealed ducts, which wreaks havoc on modern high-efficiency furnaces. A furnace that’s oversized for the duct system, or a duct system that leaks 30% of its air into the crawlspace, will short-cycle and wear out parts faster. The right answer in those homes often hinges on duct static pressure and a room-by-room load calculation, not just the age of the furnace.
We saw this firsthand at a 1960s rambler off 68th Ave NE in Kenmore where a Carrier furnace was short-cycling every few minutes on a cold snap. The homeowner assumed it was time for a replacement. Our tech found a failed capacitor on the blower motor and a clogged filter driving static pressure way too high. Replacing the capacitor and filter restored steady heat, and the homeowner avoided a $5,000-plus replacement. We also inspected the heat exchanger while we were in there, and it was sound.
We Also Serve Cities Near Kenmore
Dalton Heating & Air runs furnace repair and maintenance calls throughout the north Lake Washington area, including Bothell, Mountlake Terrace, Lynnwood, and Woodinville. If you’re in one of these communities, the same written pricing and same-day availability applies. Scheduling is coordinated from our Seattle office, with crews serving Kenmore locally.
Serving Kenmore, WA - Our Local Coverage Area
We’re based in the Kenmore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Kenmore
Check the filter first. A clogged filter restricts airflow enough that the high-limit switch trips, which shuts off the burners while the blower keeps running cold air. In Kenmore’s older homes with original ductwork, this is the single most common cause. If the filter is clean and you still have cold air, call (361) 306-9515 and we’ll diagnose it the same day.
Multiply the age of your furnace by the cost of the repair. If the furnace is 15-plus years old and the repair is more than a third of the replacement cost, replacement usually makes sense. But Kenmore’s housing stock adds another factor: if your ducts are leaky or undersized, a new furnace won’t fix the underlying problem. We’ll always run the numbers and the static pressure test before recommending either path.
A room-by-room load calculation, called a Manual J, measures each room’s heat loss based on window area, insulation, and orientation. In Kenmore, where older waterfront homes lose heat differently than newer builds inland, this determines the correct furnace size. Most furnaces installed in older Kenmore homes are oversized, which is why they short-cycle and eat parts. A load calculation prevents that.
SEER2 applies to cooling efficiency, not furnace repair. For furnaces, the relevant number is AFUE, which measures how much fuel becomes usable heat. A 20-plus-year-old furnace in a Kenmore home might still fire, but at 80% AFUE or lower, it’s wasting serious money on gas. We’ll check your system’s combustion efficiency during any maintenance visit and show you the numbers.
Yes. We’re factory-trained to service nine major residential brands, including Rheem, York, Bryant, and Daikin, among others. We carry common parts for these systems on our service vehicles, so most Kenmore repairs are done in a single visit. Call (361) 306-9515 to confirm your model and get a written price.
Call Dalton Heating & Air for Furnace Repair in Kenmore
A no-heat furnace in a Kenmore winter is not a wait-and-see problem. The cold is hard on pipes, on pets, on older family members, and on you. Call (361) 306-9515 for a free estimate. You’ll speak to a live person, we’ll schedule a tech inside a stated window, and the price will be in writing before any work begins. If the repair doesn’t hold for a full year, we come back at no charge. That’s the 365-Day Done Right Promise, and it’s how we’ve done business in Kenmore since the day we started taking calls here.
Written by Marco Benitez, Owner at Dalton Heating & Air, a Garrison Partners company serving Kenmore since 2003.