Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Kenmore
A new heat pump for a Kenmore home typically runs $3,500 to $7,500 installed, depending on whether you’re working with existing ductwork on a 1960s rambler or going ductless in a hillside townhome. We send background-checked, uniformed technicians to Kenmore every week, and we put the full price in writing before any work begins. If you’re trying to figure out whether your Kenmore house needs a load calculation before the heat pump goes in, call us at (361) 306-9515 and we’ll walk through it.
Why Dalton Heating & Air Is Kenmore’s Preferred Heat Pump Installation Company
Dalton Heating & Air has been held to The Garrison Standard since 2003, and that standard applies to every house we touch in Kenmore. We arrive inside the stated window, price the job in writing before starting, do the work by the book, and leave the site clean. Marco Benitez runs our crew, and he holds every tech to the same expectation: a heat pump install in Kenmore that is not done right gets made right, for a full year, under our 365-Day Done Right Promise.
Kenmore’s housing stock is split between 1950s and 60s ramblers near the lake with undersized ductwork and newer townhomes on the hillside built to tighter envelopes. The same heat pump tonnage and static pressure design can’t serve both. That means a proper load calculation here often ends in two different system specs on the same street. Our techs have measured static pressure on original ductwork near the Kenmore Lumber dock and installed ductless systems in new construction up in the Inglewood hills. We know what each type of Kenmore home needs.
Kenmore homeowners call us because a real person answers the phone 24/7, not a voicemail queue. We don’t make you wait for a callback window. We service all nine major residential HVAC brands including Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. If you’re in Kenmore and your heat pump decision comes down to repair versus replace, we give you honest numbers for both and let you decide.
Geothermal Heat Pump Installation in Kenmore
Geothermal Heat Pump Installation in Kenmore means burying a ground loop on your property and pairing it with an indoor unit that moves heat between your home and the earth instead of the outside air. Kenmore lots near the Sammamish River and Swamp Creek corridor sometimes have high water tables or tight setbacks that affect loop design, so we always check lot conditions before quoting. A geothermal system typically runs higher upfront than an air-source heat pump, often toward the top of the $3,500 to $7,500 range and sometimes beyond depending on loop depth and drilling conditions. What you get in return is the lowest operating cost of any heat pump type, and no outdoor condenser making noise against the side of the house.
Ground Loop Sizing for Kenmore Lots
On smaller Kenmore lots, a vertical loop drilled into the ground makes more sense than a horizontal trench. The loop depth depends on soil conditions, which vary between the sandy loam near Lake Washington and the clay-heavy soil up toward the King-Snohomish county line. We don’t guess on loop size. We use the heating and cooling load of the specific house, not a rule of thumb based on square footage alone.
When Geothermal Works and When It Does Not
A geothermal system pays off fastest on a Kenmore home with high heating demand, like a rambler with original single-pane windows that still loses heat in a 28°F January night. It makes less sense on a small townhome with a low annual heating load where a ductless heat pump will get the bills down for a much smaller install cost. We’ll tell you which direction the math points for your specific house.
Ductless Heat Pump Installation in Kenmore
Ductless Heat Pump Installation in Kenmore is the cleanest path when a house has no ductwork or ducts too small to move enough air for a central system. Many older Kenmore ramblers near the lake have original duct runs sized for a 1950s furnace that a modern heat pump simply cannot push against without the blower straining. A ductless system skips the ducts entirely. An outdoor condenser connects to slim indoor heads mounted on walls or ceilings, and each zone runs independently. Installed costs for ductless in Kenmore generally fall in the $3,500 to $7,500 range depending on the number of indoor heads and the lineset runs.
Multi-Zone Layouts for Split-Level Homes
Kenmore has a lot of split-level and tri-level homes where one central system struggles to keep the lower level warm and the upper level from overheating. A multi-zone ductless heat pump puts a head in each occupied zone and lets you set different setpoints. That solves the classic complaint we hear from Kenmore homeowners: the family room by the lake side stays cold while the upstairs bedrooms bake.
Ductless on Hillside Townhomes
The newer townhomes up the hillside near Inglewood and Arrowhead were built tight, which is good for heat retention but often leaves them short on cooling in shoulder season. A single-zone or dual-zone ductless system handles that without any duct renovation. Installation is usually doable in a day, and there’s no drywall to patch because the refrigerant lines run inside a slim chase along the exterior.
Trusted Brands We Service in Kenmore
We install and service Trane, Lennox, Goodman, and Rheem heat pumps, among the nine brands we’re factory-trained on. What that means for Kenmore homeowners is that we can match the system to your existing electrical panel capacity, your ductwork, and your actual load rather than trying to force one brand into every house. We stock common replacement parts locally for these brands, so warranty calls and repairable failures don’t leave you without heat while a part ships from a warehouse.
Common Heat Pump Installation Problems We See in Kenmore Homes
- Installing a heat pump on a Kenmore rambler without a load calculation. The old furnace tonnage was often oversized for the house. When a new heat pump goes in at the same size, it short-cycles and never runs long enough to dehumidify in spring and fall. The result is a house that feels clammy and a bill that’s higher than it should be.
- Skipping a static pressure test on older Kenmore ductwork. Duct runs from the 1950s and 60s were sized for furnaces that pushed less air. A new heat pump’s blower motor strains against undersized returns, and the SEER2 rating printed on the box never shows up on your electric bill because the motor is fighting the ductwork every cycle.
- Setting the refrigerant charge by the factory label instead of weighing it in. On a cool Kenmore day, a charge set by pressure alone lands low. An undercharged heat pump runs the compressor harder in heating mode, which shortens the life of the most expensive component. We weigh refrigerant in on every install.
- Putting a central heat pump in a Kenmore townhome with no place for the air handler. Some hillside townhomes have utility closets too small for a standard air handler and no attic space. Forcing a central system in means a cramped install and bad airflow. A ductless system usually fits better and costs less to operate.
Pricing for Heat Pump Installation in Kenmore, WA
Here’s what we quote for Kenmore work, in writing, before the job starts:
| Service | Typical Kenmore Price Range |
|---|---|
| Heat Pump Installation | $3,500 – $7,500 |
| Tune-Up | $80 – $200 |
| AC Repair | $150 – $650 |
| Furnace Repair | $150 – $700 |
The biggest variable in Kenmore is whether the existing ductwork can move the air a new heat pump needs. If it can’t, you’re looking at either duct modifications or going ductless, both of which move the price. A load calculation tells us the exact tonnage. The house on the lake side and the house on the hilltop can be the same square footage and need different systems. Call (361) 306-9515 for a free estimate with a fixed written price before we start.
We Also Serve Cities Near Kenmore
Our Heat Pump Installation team covers Kenmore and the surrounding communities. We run calls to Kenmore and also serve Bothell, Mountlake Terrace, Lynnwood, and Woodinville regularly. If you’re just outside Kenmore city limits, ask when we can get to your street when you call.
Serving Kenmore, WA - Our Local Coverage Area
We’re based in the Kenmore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Kenmore
You need a load calculation first, and we include one with every heat pump quote in Kenmore. Older ramblers near the lake and along 68th Ave NE were built with ductwork sized for an oil or gas furnace, not a modern heat pump. We measure static pressure on the existing ducts before recommending equipment. If the ducts are too restrictive, we’ll show you the numbers and give you options for duct modifications or a ductless setup. Call (361) 306-9515 to schedule the load calculation.
Most heat pump installations in Kenmore land between $3,500 and $7,500. The spread comes down to system type, ductwork condition, and the number of zones. A simple single-zone ductless install runs toward the lower end. A full central system on a rambler that needs return air upsizing lands higher. The price we quote is in writing before the work starts, and it doesn’t change when the crew arrives. For an exact number on your home, call (361) 306-9515.
SEER2 is a more demanding efficiency test meant to reflect real-world installation conditions, so the ratings dropped across the board even though the equipment itself got more efficient. In Kenmore, what matters for your bill is whether the system’s static pressure matches the design. A SEER2 rated system crammed onto undersized 1960s ductwork will not hit its efficiency number. A properly sized and matched system will. We test static pressure and airflow on every install, because that’s the difference between the rating on the box and the number on your bill.
If your heat pump is under 10 years old and the failed part is a capacitor, contactor, or defrost board, repair is usually the right call. Those repairs in Kenmore run $150 to $650. If the compressor has failed or the system is over 15 years old and leaking refrigerant, replacement starts to make more sense than pouring money into an aging unit. We’ll give you the repair cost and a replacement quote side by side so you can compare real numbers, not a sales pitch. Call (361) 306-9515 and we’ll run the numbers on your specific system.
We install ductless mini splits, geothermal heat pumps, and standard air-source heat pumps in Kenmore. Ductless fits the older lakefront ramblers and the newer townhomes equally well, and geothermal works on Kenmore lots with enough room for a ground loop. We don’t push one system type on every house. The load calculation and your lot conditions determine what we recommend. Call (361) 306-9515 for a free estimate on any heat pump type.
Call Dalton Heating & Air at (361) 306-9515 for a free, written heat pump installation estimate in Kenmore. Marco Benitez and our crew will walk you through the options, give you a fixed price, and stand behind the work for a full year under the 365-Day Done Right Promise.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Kenmore and surrounding communities.