Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Clarkston
Heat pump installation in Clarkston typically costs $3,500 to $7,500 for a complete system replacement, with most ranch homes on the north side of town landing between $4,200 and $5,800 depending on tonnage and duct condition. Our Heat Pump Installation team runs calls into Clarkston daily, and we schedule most replacements within three to five business days once the equipment is confirmed. Call (361) 306-9515 and you’ll talk to a live person who can get a written estimate scheduled – no voicemail queue, no callback window.
Why Dalton Heating & Air Is Clarkston’s Preferred Heat Pump Installation Company
Clarkston homeowners have a specific set of frustrations with HVAC companies, and we hear them on nearly every estimate: the crew that shows up three hours late, the quote that changes at the door, the job left with panels off and cardboard in the yard. That’s not how Dalton Heating & Air operates. Every job gets a written price before any work starts, every repair carries a written guarantee for a full year, and if something fails in that window, we return at no charge. Marco Benitez runs our Clarkston service area under The Garrison Standard, the same operating discipline Garrison Partners has held since 2003: arrive inside the stated window, do the job by the book, leave the site clean, stand behind the work.
Response time to Clarkston from our dispatch desk in Atlanta runs 45 to 90 minutes for most calls, quicker if the job is off Ponce de Leon Avenue or near the high school. We answer the phone with a live person 24 hours a day, which matters when your heat pump dies on a July afternoon and the house is climbing past 85 degrees. Our technicians are background-checked and uniformed, and you’ll know their name before they pull into your driveway.
Heat Pump Service in Clarkston
Heat pump service in Clarkston usually means a system that’s running but not running right: short cycling, weak airflow, ice on the outdoor coil, or a thermostat that can’t hold setpoint. Most heat pump service calls in Clarkston run $150 to $650 depending on what’s actually wrong. A failed capacitor or contactor sits at the low end. A refrigerant recharge, where we top off the cooling fluid your system needs to reach temperature, runs higher and usually means there’s a leak we need to find. We don’t patch and run – if the repair doesn’t hold, we’re back at no charge.
Diagnostics and Same-Day Repair
When a Clarkston heat pump quits, our technician starts with static pressure, subcooling, and superheat readings before touching anything else. That tells us whether the problem is electrical, mechanical, or refrigerant-related – and it keeps us from selling you a compressor when you only need a capacitor. Most service calls, we can get the system running same day.
Seasonal Tune-Ups
A heat pump runs year-round in Georgia, so it wears twice as fast as a furnace or an air conditioner that only works half the year. We recommend a tune-up in early spring and again in fall. The cost runs $80 to $200, and you get a written report of what we found – coil condition, refrigerant levels, capacitor health, amp draws – so you know what’s holding and what might fail next.
Heat Pump Replacement in Clarkston
Heat pump replacement in Clarkston means pulling an old or failed unit and putting in a properly sized system, and that job runs $3,500 to $7,500 for a complete install. The spread comes down to tonnage, brand, and whether your existing ductwork can handle the new system. A 2.5-ton replacement in a standard Clarkston ranch runs closer to the low end. A 4-ton system with duct sealing and modifications lands near the top. We write the price before we order equipment, and that number doesn’t move.
When Replacement Beats Repair
The honest threshold is this: if the repair cost tops 40% of the replacement cost and the system is over 12 years old, replacement usually makes more sense. A $650 compressor job on a 14-year-old unit that’s already leaking refrigerant is money you won’t get back. We’ll walk you through the math in plain numbers, not sales pressure.
Load Calculation Before Any Equipment Order
We don’t size a Clarkston heat pump by square footage alone. Ever. We run a full Manual J load calculation – measuring window orientation, insulation depth, duct leakage, and east-facing sun exposure – before we quote a single ton. This is where a lot of companies cut corners, and it’s exactly why so many Clarkston homes have oversized systems that short cycle and eat compressors.
Trusted Brands We Service in Clarkston
Dalton Heating & Air installs and services Trane, Lennox, Goodman, and Rheem heat pumps, and we keep common replacement parts on our trucks for Clarkston jobs – capacitors, contactors, defrost boards, and thermostats. That means less waiting on a parts order when your system is down. If you’re replacing a unit and want a brand recommendation, we’ll give you a straight answer based on your home’s layout and ductwork, not a manufacturer kickback. That’s the Garrison Standard: the right equipment for the house, not the right equipment for our margin.
Common Heat Pump Installation Problems We See in Clarkston Homes
- Oversized units installed off square footage alone. Clarkston’s humid summers punish an oversized heat pump – it short cycles, never pulls enough moisture out of the air, and the compressor fails years early. A proper load calculation fixes this before the equipment is ordered.
- Incorrect refrigerant charge after installation. A heat pump that’s overcharged or undercharged freezes the evaporator coil in summer and loses heating capacity in winter. We verify charge with a digital manifold on every install, not a guess.
- Leaky ductwork throwing off static pressure. Older Clarkston ranch homes on the north side of town have duct runs that leak 20 to 30 percent of conditioned air into attics and crawl spaces. Sealing those runs before install keeps the new heat pump from working against itself.
- Voltage sag on older Clarkston circuits. Some 1960s-era panels in Clarkston drop voltage under load, which stresses compressor capacitors. We check supply voltage during every install and flag it when it’s out of spec.
Pricing for Heat Pump Installation in Clarkston, GA
Here’s what a Clarkston homeowner should expect to pay, in writing, before any work starts:
| Service | Price Range in Clarkston |
|---|---|
| Heat Pump Installation | $3,500 – $7,500 |
| Heat Pump Service | $150 – $650 |
What moves the number: tonnage, brand, ductwork condition, and whether we’re doing a like-for-like swap or correcting an existing sizing problem. A 2-ton replacement in a tight Clarkston townhome near the PATH trail runs less than a 4-ton install in a sprawling ranch off Montreal Road where the ducts need sealing. Estimates are free, they’re in writing, and they don’t change at the door.
We Also Serve Cities Near Clarkston
Dalton Heating & Air runs heat pump jobs throughout the Clarkston area, including Clarkston‘s neighboring communities. If you’re in Scottdale, Stone Mountain, Tucker, or Decatur and need a straight answer on heat pump repair or replacement, call (361) 306-9515 and we’ll get you scheduled. Same written pricing, same one-year guarantee, no matter which side of the county line you’re on.
Serving Clarkston, GA - Our Local Coverage Area
We’re based in the Clarkston area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Clarkston
A good rule of thumb: if the repair cost is under 40% of replacement cost and the system is under 12 years old, repair it. If the compressor is failing, the refrigerant is leaking, or the unit is past 15 years, replacement is usually the better money. In Clarkston specifically, we see a lot of original heat pumps from the 1990s still limping along in older ranch homes – they’re past their service life and replacing them with a modern SEER2 unit typically cuts the electric bill by 30 percent or more. Call (361) 306-9515 and we’ll give you an honest repair-versus-replace recommendation with numbers behind it, not a sales pitch.
Most Clarkston ranch homes built in the 1960s and 70s need 2.5 to 3 tons, not the 3.5 to 4 tons that square footage alone would suggest. The reason is ductwork – those original ducts are often undersized or leaking, and a bigger heat pump pushing against them creates static pressure problems that shorten compressor life. A Manual J load calculation tells us the right tonnage for your specific house. It’s the only honest way to size a system, and we run it on every replacement we quote.
Clarkston’s hot, humid summers and mild winters are actually ideal heat pump territory. A heat pump moves heat instead of creating it, which is why it runs efficiently year-round here – it cools through the summer and heats through the winter without a gas line or electric strips. The humidity is the wildcard. A properly sized heat pump dehumidifies as it cools, but an oversized unit short cycles and never pulls enough moisture. That’s why load calculation matters more in Clarkston than in drier climates farther west.
A load calculation often shows that Clarkston homes need a smaller-tonnage heat pump than the square footage suggests, because the original ductwork can’t handle the static pressure of a larger unit. We replaced a failed 2-ton Goodman heat pump at a ranch home off Montreal Road with a Carrier 3-ton unit after our load calculation revealed the original system was undersized for the home’s east-facing sun exposure. We also corrected the refrigerant charge and upgraded the capacitor to handle Clarkston’s voltage swings. The homeowner’s summer bills dropped noticeably, and the system now heats efficiently through mild Georgia winters. That’s what a real load calculation changes – the system fits the house instead of fighting it.
Often it’s the capacitor, which costs $150 to $300 to replace in Clarkston and fixes the problem same day. But if the outdoor unit runs and the air still isn’t cold, you’re likely looking at a refrigerant leak or a failing compressor – and those run higher. The only way to know is to check the capacitor’s microfarad reading and the system’s refrigerant pressures. A bad capacitor left running can damage the compressor, so it’s worth getting a technician out quickly. Call (361) 306-9515 and we’ll diagnose it straight, with the price in writing before we touch anything.
Get a Straight Answer on Heat Pump Installation in Clarkston
If your Clarkston heat pump is struggling or dead, call (361) 306-9515. You’ll get a live person, a scheduled window we actually hit, and a written estimate before any work begins. Marco Benitez and the Dalton Heating & Air team run heat pump jobs across Clarkston daily – from the ranch homes off Montreal Road to the newer townhomes near the PATH trail – and we stand behind every install for a full year with the 365-Day Done Right Promise. If it’s not done right, we make it right. That’s the deal.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving the Clarkston area under The Garrison Standard since 2003.