Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Newton
Furnace repair in Newton, MA typically runs $150 – $700 depending on the failed part, and most no-heat calls get a same-day visit. We’re talking about the difference between a $22 ignitor and a cracked heat exchanger that means replacement, so we give you a written price before any work begins. Dalton Heating & Air crews know Newton’s streets, from Commonwealth Avenue to the side roads off Centre Street. If your furnace is down and the house is cold, call (361) 306-9515 and a live person answers, 24 hours a day.
Why Dalton Heating & Air Is Newton’s Preferred Furnace Repair Company
The Garrison Standard has governed our work since 2003, and it’s not a marketing slogan. It’s a working code: arrive inside the window, put the price in writing before touching a screwdriver, do the job by the book, leave the site clean, and stand behind the repair for a full year. Newton homeowners who have dealt with no-shows and door-step price changes tend to appreciate that kind of discipline. We serve Newton from our Boston metro dispatch office, so scheduling stays local and predictable.
Every tech who shows up at your door is background-checked, uniformed, and factory-trained on nine major HVAC brands including Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. You’ll know who’s coming before they arrive. And if a repair fails inside the 365-day guarantee window, we return at no charge. Not a pro-rated credit. A second visit, free.
Our Furnace Repair team also handles boiler work, which matters in Newton. A lot of Newton’s housing stock predates forced air entirely, and we’ll get into that below. The point is: we don’t send a furnace tech to look at a boiler and hope for the best. We send someone who knows both.
Boiler Repair in Newton
Boiler repair in Newton usually means working on original cast-iron radiators, copper baseboard, or mid-century hydronic systems, and it typically runs $150 – $700 depending on whether we’re replacing a circulator pump, an expansion tank, a pressure relief valve, or a gas valve. Newton has a lot of pre-war homes that never had ductwork, so boilers are everywhere in this city. When one quits in January, you feel it fast.
Circulator and Zone Issues
A boiler that fires but won’t push heat to the radiators usually points to a failed circulator pump or a stuck zone valve. We see this a lot in older Newton Colonial homes with multiple heating zones that haven’t been serviced in years. The fix is often the same day, and the part is common enough that we stock it on trucks serving Newton.
Pressure and Expansion Problems
Boilers run on pressure, and when the expansion tank fails, the system overpressures and the relief valve starts dripping or the boiler short-cycles. In older Newton homes where boilers sit in basements that also house finished spaces, that drip can damage floors and drywall before anyone notices. We check the whole loop, not just the part that’s making noise.
Gas Furnace Repair in Newton
Gas furnace repair in Newton starts at about $150 for a diagnostic plus common part replacement and runs up to $700 when the job involves a blower motor, an inducer assembly, or a gas valve that needs replacing. Newton’s gas furnaces range from 1990s Carrier units in the Highlands to newer Goodman and Rheem systems in Waban and Newton Centre. We stock common parts for those brands locally, so we’re not waiting on a warehouse in another state when your house is at 52 degrees.
Ignitor and Flame Sensor Failures
A furnace that clicks but won’t light usually has a failed hot-surface ignitor or a dirty flame sensor. Both are quick fixes, and we carry them on the truck for most models. If you’ve got a furnace that lights, runs for a minute, then shuts off, that’s the flame sensor telling the board there’s no flame when there is. We clean or replace it on the spot.
High-Limit Trips and Short Cycling
When a furnace trips its high-limit switch, it’s overheating, and that’s usually an airflow problem: a dirty filter, a failing blower motor capacitor, or a clogged evaporator coil sitting on top of the furnace. In Newton, where a lot of equipment sits in tight basement mechanical rooms, airflow is already compromised. We measure static pressure and verify actual airflow before we just reset the switch and leave. A furnace that trips the limit repeatedly is trying to tell you something, and the answer is rarely “keep pressing reset.”
Trusted Brands We Service in Newton
We carry parts and factory training for six major residential brands most common in Newton: Goodman, Rheem, York, and Daikin among them. Goodman is everywhere in this city’s mid-century ranches and split-levels. Rheem shows up in a lot of newer renovations in Waban. York and Daikin are common in high-efficiency retrofits around Newton Centre and Newtonville. We stock ignitors, flame sensors, pressure switches, and control boards for these brands on our local trucks, which means fewer return trips and faster repairs for Newton customers. If you’ve got a Carrier, Trane, Lennox, Bryant, or American Standard, we service those too.
Common Furnace Repair Problems We See in Newton Homes
- Cracked heat exchangers in older induced-draft furnaces. Newton’s Victorian and Colonial stock has a lot of furnaces pushed into old boiler rooms with chimneys that were never right for the equipment. An undersized or orphaned flue stresses the heat exchanger, and eventually it cracks. We test with a combustion analyzer and a visual inspection on every safety-related call.
- Short cycling from oversized equipment. A lot of Newton homes got new furnaces installed without a Manual J load calculation. The result is a furnace that’s too big for the house, so it fires, overshoots, and shuts down. That wears out ignitors, blower motors, and control boards faster than anything else.
- Failed blower motor capacitors. Cold snaps in Newton are when capacitors fail, because the motor draws more current in the cold and the capacitor is already ten years old. The symptom is a furnace that fires but the blower won’t start, and the high-limit shuts everything down. We replace the capacitor and the blower usually comes right back.
- Dirty evaporator coils choking airflow. The coil sits above the furnace, and when it’s clogged with years of dust and pet hair, the furnace can’t move air, so the high limit trips and the house stays cold. Newton homes with central AC and forced air see this constantly, especially where basement mechanical rooms don’t get regular filter changes.
Pricing for Furnace Repair in Newton, MA
| Service | Typical Price Range |
|---|---|
| Furnace Repair (diagnostic + common part replacement) | $150 – $700 |
| Boiler Repair | $150 – $700 |
| Tune-Up | $80 – $200 |
What pushes a repair toward the high end of that range is the part itself: a gas valve costs more than an ignitor, and a blower motor costs more than a capacitor. The diagnostic and labor stay predictable. You get the price in writing before any work starts, every time. No exceptions. If you’re comparing Newton HVAC companies, ask whether the quote includes the diagnostic fee or tacks it on top. Ours is part of the written price, not a separate line item. Call (361) 306-9515 for a free estimate on any furnace repair in Newton.
We Also Serve Cities Near Newton
Dalton Heating & Air handles furnace repair across Newton and the surrounding towns, including Belmont, Brookline, Cambridge, and Waltham. If your furnace is down and you’re near the Newton line, call (361) 306-9515 and we’ll get you scheduled from the Boston dispatch office, same as we do for our Newton customers.
Serving Newton, MA - Our Local Coverage Area
We’re based in the Newton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Newton
If the furnace is under 12 years old and the repair is under $700, repair is usually the right call. If it’s over 15 years old and the heat exchanger is cracked, Newton Heat Pump Installation or full replacement is worth considering. The heat exchanger is the part that separates combustion gases from the air you breathe, and once it’s cracked, the repair cost approaches half the price of a new furnace and you still have an old furnace. We’ll give you honest numbers for both options before you spend anything. Call (361) 306-9515 and we’ll walk through it with your actual equipment, not a generic chart.
A load calculation tells you the exact BTU output your home needs. If your current furnace is oversized, you’ve been living with short cycling and humidity swings. If it’s undersized, it runs nonstop in January and still can’t hold temperature. The right furnace sized with a Manual J calculation runs less, lasts longer, and costs less to operate every month. Whatever we repair, we won’t sell you a replacement without one. That’s the standard in Newton, or it should be.
SEER2 is the updated efficiency rating for cooling, but it matters for your heating bill because it applies to heat pumps and to the overall efficiency testing of new equipment installed after 2023. For a gas furnace in Newton, the more relevant number is AFUE, which measures how much of your fuel dollar becomes heat. A 95% AFUE furnace wastes 5 cents of every gas dollar up the flue. A 2005-era 80% furnace wastes 20 cents. Over a Newton winter, that’s real money. Check ENERGY STAR and AHRI for efficiency ratings on any new equipment before you decide.
Yes. Newton has a lot of hydronic heating, and our boiler repair team handles circulator pumps, expansion tanks, gas valves, pressure switches, and zone controls on every major boiler type. Boiler repair runs $150 – $700, same range as forced-air furnace repair. If you’ve got radiators and the house is cold, we’re set up for it. Call (361) 306-9515.
Most no-heat calls in Newton get a same-day visit, and our schedule is managed out of the Boston office with crews staged to reach Newton, Newtonville, Waban, and Newton Highlands quickly. You call, a live person answers, and we give you a real arrival window. If your heat is out and the temperature is dropping, call (361) 306-9515 now and we’ll get you on the schedule.
Written by Marco Benitez, Owner at Dalton Heating & Air. Dalton Heating & Air is a Garrison Partners company, independently owned and operated, serving Newton and the surrounding towns.