Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Edison
Furnace repair in Edison, NJ typically runs $150 – $700 depending on the part that failed, and most jobs are completed in a single visit. We dispatch crews to every Edison neighborhood from our New York City office, and a real person answers the phone 24/7 at (361) 306-9515. You won’t get a voicemail queue, and you won’t wait on a callback window. If your furnace is down on a January night, the price is in writing before we touch a screw, and the repair is guaranteed in writing for a full year.
Edison’s housing stock is not one-size-fits-all. The homes off Route 27, the colonials near Woodbridge Avenue, the older wood-frame houses toward the Metuchen border – they all fail differently, and a furnace fix that works on one won’t necessarily hold on another. That’s why we send factory-trained techs who know what they’re looking at before they open the panel.
Why Dalton Heating & Air Is Edison’s Preferred Furnace Repair Company
Dalton Heating & Air has been operating under The Garrison Standard since 2003, and every job in Edison follows the same five-point Garrison Code: arrive inside the stated window, put the price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. That’s not a sales line. It’s the operating rule on every call we run in Edison.
Our Furnace Repair team works on nine major residential HVAC brands, so you don’t need to call around to find someone who knows your Carrier or Trane system. Marco Benitez, who leads our location, holds every tech to the same written-pricing rule: the number on the estimate is the number on the invoice. If a repair fails within the guarantee period, we return at no charge – that’s the 365-Day Done Right Promise, and it applies to every service call in Edison.
Every technician who comes to your door is background-checked and uniformed. You’ll know the name before they arrive. No subcontractors, no side crews, nobody who quotes one price over the phone and a different one at the door.
Heat Pump Repair in Edison
Heat Pump Repair in Edison usually means one of three things: a refrigerant leak, a failed reversing valve, or an outdoor unit that’s iced over and can’t defrost. Edison homes built in the last two decades often have heat pumps paired with ducted air handlers, and when the reversing valve sticks in cooling mode, your heat pump will blow cold air in the middle of winter. That’s a repair, not a replacement – and it typically runs $150 – $650 depending on the specific part.
What Actually Breaks on a Heat Pump
Losing heat from a heat pump is not the same as a furnace failure. The compressor is still running, but the refrigerant may be low, or the defrost board isn’t cycling. On a call in the Clara Barton section, we found a heat pump that was switching to aux heat every 10 minutes because the outdoor temperature sensor had failed. A $220 part swap brought it back to normal operation.
When a Heat Pump Repair Is Not the Answer
If the heat exchanger in the indoor air handler has failed, or if the compressor is grounded out, the repair math changes fast. We’ll tell you plainly when a heat pump has one more season in it – and when it doesn’t. Edison winters may not be brutal, but they’re cold enough that a heat pump limping along on emergency heat will spike your electric bill. A straightforward repair beats a patch job every time.
Heating Repair in Edison
Heating Repair in Edison is the call we run most from late October through early March, when the temperature swings start and furnaces that sat idle through the summer wake up hard. The job involves diagnosing the specific failure – ignitor, gas valve, flame sensor, blower motor, or heat exchanger – and then fixing it with the part that actually matches the system, not a universal aftermarket substitute. Edison heating repairs typically run $150 – $700.
Gas Furnace Failures We See Every Winter
Short cycling is the big one in Edison’s post-war ranches, and it usually means the furnace is oversized for the house. When a furnace undersized or oversized wasn’t checked against a load calculation, the burners fire, the plenum temp spikes, and the high-limit switch trips. That cycle of overheat-then-shutoff takes years off a heat exchanger. We see cracked heat exchangers on furnaces that aren’t even 12 years old, directly caused by that cycling pattern.
Airflow Problems That Get Misdiagnosed
If your furnace runs but the airflow is weak, the problem is rarely the blower motor itself. In Edison homes with original ductwork, we find crushed returns, disconnected runs in unconditioned crawlspaces, and undersized ducts that spike the static pressure. We got a no-heat call from Grove Avenue in the Clara Barton neighborhood – the blower motor was pulling high amps and had cooked itself after several seasons of fighting an undersized return. We replaced the blower, corrected the return, and the system has held steady through two winters since.
Trusted Brands We Service in Edison
Our techs are factory-trained on Rheem, York, Daikin, and Bryant systems, along with the rest of the major residential brands. We keep common pilot assemblies, flame sensors, pressure switches, and blower motors in local parts stock so a routine furnace repair in Edison doesn’t wait on a warehouse shipment. If your York gas valve or Rheem ignitor has failed, we typically have the right replacement part available the same day. No universal parts that sort-of fit. The part goes in, the static pressure gets checked, and the system runs the way it was designed to.
Common Furnace Repair Problems We See in Edison Homes
- Oversized furnaces in post-war ranches: Along Woodbridge Avenue and the streets off it, homes built in the 1950s and 60s often have furnaces that were never sized with a proper load calculation. The short cycling cracks heat exchangers years before they should fail.
- High static pressure from old ductwork: Edison homes with original ducts, especially in older neighborhoods near the Metuchen border, often have crushed or disconnected runs in unconditioned crawlspaces. That high static pressure burns out blower motors and trips the high-limit switch.
- Ignition and flame sensor failures after power surges: The older sections of town near the train station see voltage fluctuations that take out ignition controls and dirty up flame sensors faster than in newer developments. The symptom is a furnace that fires briefly, then locks out.
- Frozen condensate lines in high-efficiency furnaces: Furnaces with 90%+ AFUE ratings, common in Edison’s newer construction, produce condensate that can freeze in exterior drain lines during cold snaps. The furnace shuts down on a pressure switch fault even though the heat exchanger is fine.
Pricing for Furnace Repair in Edison, NJ
The most common furnace repairs in Edison fall between $150 and $700. A flame sensor replacement runs $150 – $250. An ignitor swap is $200 – $350. A gas valve replacement lands at $350 – $650. A blower motor runs $400 – $700 depending on the ECM or PSC type. Every job gets a written price before any work begins, so the number you approve is the number you pay. Estimates are free – call (361) 306-9515 and a live person will schedule the visit.
| Service | Typical Cost in Edison |
|---|---|
| Furnace Repair | $150 – $700 |
| Heat Pump Repair | $150 – $650 |
| Heating Repair | $150 – $700 |
| Tune-Up | $80 – $200 |
We Also Serve Cities Near Edison
Our techs run calls throughout the surrounding area, including Elizabeth, Newark, Bayonne, and Jersey City. If you’re just outside Edison and the furnace goes down, the same written pricing and 365-Day Done Right Promise apply. Call (361) 306-9515 and tell us the city – we’ll confirm the next available window right then.
Serving Edison, NJ - Our Local Coverage Area
We’re based in the Edison area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Edison
If the furnace is from the 1950s, replace it. A furnace that age has likely been oversized since day one, which means the heat exchanger has been expanding and contracting through tens of thousands of short cycles. Repairing it would mean putting money into a cabinet whose efficiency and safety margins are gone. In Edison, the repair-vs-replace math tilts hard toward replacement once a furnace passes roughly 20 years, and the load calculation that was never done in the first place is the first thing we do before sizing a new system. Call (361) 306-9515 for a written replacement quote and we’ll walk through the numbers honestly.
Most furnace repairs in Edison run $150 – $700. The range covers a $150 flame sensor on the low end to a $700 blower motor on the high end. The exact total depends on which part failed and whether the system needs additional airflow corrections afterward. Every diagnostic includes the repair price in writing before we touch the system, and the estimate is free. Call (361) 306-9515 and we’ll tell you the most likely range for your symptoms before we even schedule the visit.
SEER2 is the updated efficiency standard for heat pumps and air conditioners, and it measures cooling efficiency under more realistic test conditions than the older SEER rating. It matters for your heating because a heat pump with a poor SEER2 rating costs more every month to run, especially during cold snaps when the system shifts to auxiliary heat. If your repair estimate is ballooning on an older heat pump in Edison, compare the repair cost against a new system’s efficiency – sometimes the monthly savings pay for the replacement inside five years.
Cold air from a heat pump usually means one of three things: low refrigerant, a failed reversing valve, or the system is stuck in defrost. A refrigerant leak is a repair that starts around $300 and climbs if the leak is in the indoor coil. A reversing valve failure runs $450 – $650. A stuck defrost board can be as cheap as $200. We’ll diagnose it and give you the price in writing before any work begins. Call (361) 306-9515 for an exact quote.
We’re factory-trained on nine major residential HVAC brands, including Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. If your furnace falls outside that list, we can still diagnose it – the failure modes are the same even if the badge is different. Tell the dispatcher the brand when you call (361) 306-9515 and we’ll confirm the right tech for the job.
Dealing with a furnace that won’t start or a heat pump blowing cold? Call Dalton Heating & Air at (361) 306-9515. We answer live, 24/7, and we’ll give you a written price before any repair begins. If it fails within a year, we return at no charge. That’s the standard in Edison.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Edison since 2003.