Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Alderwood Manor
Furnace repair in Alderwood Manor typically runs $150 – $700 depending on the part that failed. Most no-heat calls get a same-day visit. Dalton Heating & Air answers the phone with a live person 24/7 and puts a written price in front of you before any work starts. If you’re sitting in a cold house near 168th St SW or up around Beverly Acres, call (361) 306-9515 and we’ll get a uniformed, background-checked tech to your door inside a stated window. That’s the standard we’ve held since 2003, and it applies on every job in Alderwood Manor, no exceptions.
Why Dalton Heating & Air Is Alderwood Manor’s Preferred Furnace Repair Company
The 1960s through 1980s ranch homes that make up a big share of Alderwood Manor’s housing stock have furnace closets built on low slabs, with duct runs that are longer than what you’d see in newer construction. Our techs know those layouts because we work them every week during heating season. When a homeowner on 35th Ave W calls about a furnace that fires and then quits, we don’t send a parts swapper. We send someone who knows to check static pressure first, because restricted airflow is often what’s killing the component, not the component itself.
Marco Benitez runs our team here, and he holds every tech to The Garrison Code: arrive inside the stated window, price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year through our 365-Day Done Right Promise. That guarantee is printed on every repair invoice in Alderwood Manor, not offered as an add-on. If the repair fails in that year, we return at no charge. Dispatch and scheduling for Alderwood Manor are coordinated from our Seattle office, and crews serve the area locally.
Heating Repair in Alderwood Manor
Heating Repair in Alderwood Manor is the service most homeowners call us for when the furnace starts making a new noise, the thermostat stops matching the room temperature, or the system fires and shuts down before the house warms. The job typically involves diagnosing the ignition sequence, testing the blower motor and capacitor, checking gas pressure, and pulling the flame sensor to inspect it. Most heating repairs in this area settle between $150 and $700, with the final number written down before we touch a tool.
Ignitor and Flame Sensor Work
A furnace that tries to light and then gives up is often a dirty flame sensor or a cracked ignitor, not a dead system. We test both with a multimeter and replace only what’s failed. This is the tune-up-adjacent work that looks dramatic but rarely is.
Blower Motor and Capacitor Repairs
Short-cycling in Alderwood Manor’s ranch homes frequently traces to a capacitor that’s drifted out of spec or a blower motor pulling too many amps. We check amp draw against the nameplate, not guesswork. If the motor is running hot because the ducts are undersized, we tell you that plainly because swapping the motor without fixing the airflow leaves you with the same failure in another year or two.
Boiler Repair in Alderwood Manor
Boiler Repair in Alderwood Manor covers hydronic systems in the older split-level and custom homes scattered through the area, where radiators or baseboard loops replace forced air. The work often means a failing zone valve, a circulator pump that’s lost pressure, or an airlock in the loop. Boiler repairs here run within the same $150 – $700 band, though labor can lean higher when a tech needs to drain and refill multiple zones.
Circulator Pump and Zone Valve Service
When one room stays cold while the rest of the house heats fine, the problem usually sits in a zone valve that won’t open or a circulator pump that’s not moving water. We test voltage at the valve, check the pump’s impeller, and replace only the failed part. No boiler swap unless the heat exchanger says otherwise.
Air Removal and Pressure Checks
A bubbling sound from the baseboards means air in the system, which drops system pressure and cuts efficiency. We purge the loops and verify the expansion tank is holding. This is boiler tune-up work as much as repair work, and the price lands on the lower end of our range.
Trusted Brands We Service in Alderwood Manor
Our techs are factory-trained on Rheem, Bryant, and York, plus six other major residential brands: Carrier, Trane, Lennox, Goodman, Daikin, and American Standard. That matters when a specific control board or draft inducer needs replacing. We keep common parts local for Alderwood Manor customers, and when something isn’t on the truck, we have direct supply lines that turn most multi-day waits into next-day fixes. No matter the brand on the nameplate, the repair still carries the full 365-day written guarantee. The price is still in writing before work begins.
Common Furnace Repair Problems We See in Alderwood Manor Homes
- Short-cycling from a weak capacitor or failing blower motor. Many of these 1960s – 1980s furnaces were installed before modern load calculations, so they’re oversized for today’s tighter envelopes and fire too often. The motor wears out faster, and the cycle repeats.
- Heat exchanger cracks in 20-plus-year-old units. Long winter run cycles against undersized returns and high static pressure stress the metal until it fails. A cracked heat exchanger is a safety issue, not a patch job, and we’ll show you the crack before discussing replacement.
- Thermostat calibration drift and dirty flame sensors. These cause intermittent no-heat calls that look like full system failures. Often they’re simple tune-up items in Alderwood Manor, fixed in under an hour at the low end of our price range.
- Ignition lockouts on cold mornings near Beverly Lake. Moisture from the lake’s microclimate and older venting can foul sensors faster here. We clean, test, and reset, then show you how to avoid a repeat before next winter.
Pricing for Furnace Repair in Alderwood Manor, WA
Most furnace repairs in Alderwood Manor land between $150 and $700. Here’s the breakdown:
| Service | Typical Price Range |
|---|---|
| Furnace Repair | $150 – $700 |
| Tune-Up | $80 – $200 |
| Furnace Replacement (with load calculation) | $3500 – $7500 |
What moves a repair toward the top of that range is parts, not labor padding. A failed gas valve or control board costs more than a flame sensor. Before we order anything, you get a written price that covers parts, labor, and the full-year guarantee. Estimates are free, and there’s no obligation to proceed. Call (361) 306-9515 and ask for Marco’s team to walk you through it.
We Also Serve Cities Near Alderwood Manor
Our Furnace Repair crews cover Alderwood Manor and the surrounding area, including Seattle, Spokane, Tacoma, and Vancouver. If you’re just outside the immediate neighborhood, call and we’ll confirm coverage. For local context specific to this area, see our page on Furnace Repair in Alderwood Manor.
Serving Alderwood Manor, WA - Our Local Coverage Area
We’re based in the Alderwood Manor area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Alderwood Manor
A short-cycling furnace in Alderwood Manor is usually a repair first: a weak capacitor, failing blower motor, or overheating limit switch. But if the unit is oversized for your home, which is common in 1960s – 1980s ranch builds here, the cycling will return until the sizing is corrected. We diagnose the part, run a load calculation if the system is over 15 years old, and show you the math before recommending anything. Call (361) 306-9515 for a written assessment.
Yes, and it’s non-negotiable with us. A load calculation measures your home’s actual heating demand in square footage, insulation, window orientation, and duct capacity, and it’s the only way to avoid installing an oversized furnace that short-cycles or an undersized one that runs constantly. We pair it with a static pressure test on every replacement quote in Alderwood Manor. The load calculation is included in the replacement price range above, not billed as an add-on.
SEER2 is the updated federal efficiency rating for heat pumps and air conditioning, measuring cooling output against energy use under real-world conditions. For furnaces, the relevant number is AFUE, not SEER2, but if your quote includes a heat pump alongside the furnace, SEER2 tells you how that unit will perform. Higher SEER2 means lower summer electric bills, but the winter heating side still depends on proper sizing. A quote with no load calculation behind the efficiency numbers is just marketing.
Same-day in nearly all cases. We prioritize no-heat calls because a cold house in a Puget Sound winter isn’t an inconvenience, it’s a health and pipe-freeze risk. When you call (361) 306-9515, a live person answers, schedules a window, and a uniformed tech arrives inside it. Emergency dispatch runs 24/7, and there’s no overtime charge on top of our standard repair pricing.
Yes, we service boilers and furnaces side by side. Alderwood Manor has enough hydronic systems in older split-level and custom homes that we keep boiler parts, circulator pumps, and zone valves in the truck. Boiler repair falls under the same $150 – $700 range and carries the same 365-day written guarantee. Whether it’s forced air or baseboard heat, the price is in writing before we start.
Call Dalton Heating & Air for Furnace Repair in Alderwood Manor
If your furnace is short-cycling, running loud, or not running at all, call (361) 306-9515. You’ll speak with a real person, get a same-day window, and receive a written price before any work starts. Marco Benitez and our Alderwood Manor team stand behind every repair for a full year through the 365-Day Done Right Promise. If the work doesn’t hold, we come back at no charge. That’s the standard since 2003.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Alderwood Manor and the surrounding area.