Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Heat Pump Installation Across Selma
A new heat pump installed in Selma typically runs $3,500 to $7,500, and most replacements take one full day with a two-person crew. That’s the honest range, in writing, before any work begins. We’re Dalton Heating & Air, a Garrison Partners company operating since 2003, and our crews roll out to Selma for load calculations, full system swaps, and geothermal work without the pricing games you may have dealt with before. Call (361) 306-9515 for a free estimate on Heat Pump Installation anywhere in Selma, and you’ll get a written price, not a guess.
Selma’s real consideration isn’t whether a heat pump works here. It’s whether the installer accounts for fog-belt humidity and defrost behavior before sizing the unit. That changes what we quote, what we install with our Heat Pump Installation in Selma, and how it runs for the next 15 years.
Why Dalton Heating & Air Is Selma’s Preferred Heat Pump Installation Company
Selma homeowners call us because they’re done with no-shows and door prices that shift. We put the price in writing before any work starts, every job, no exceptions. That’s The Garrison Standard, and it applies whether we’re replacing a 2-ton unit off Floral Avenue or quoting geothermal for a larger property near the Selma Cemetery District.
Our technicians are background-checked and uniformed. You’ll know who’s coming before they arrive. And when you call, a live person answers, 24/7, no voicemail queue.
We’ve done enough work in Selma to know the local housing stock: mid-century ranches with undersized returns near the downtown corridor, newer two-story builds east of Highway 99, and older farm-adjacent properties near Fowler and Parlier where orchard dust settles into condenser coils every harvest. That local knowledge shapes how we size equipment and where we recommend placing the outdoor unit.
Contact Heat Pump Installation in Selma support through Dalton Heating & Air any time. Our phone is answered by a real person, and our estimator will give you a straight answer on cost, timeline, and whether a repair makes more sense.
Heat Pump Maintenance in Selma
Heat Pump Maintenance in Selma is a twice-yearly service, spring and fall, and it costs $80 – $200 per visit. It’s the single cheapest way to keep a heat pump from eating through defrost cycles in January fog or dragging through the July heat with a fouled coil. In our Selma work, we find that fog-belt humidity makes coil cleaning and defrost board checks more important than they are for other Central Valley cities.
Defrost Board and Charge Verification
We check the defrost board settings and the refrigerant charge by the written spec on the data plate. A board stuck on a 30-minute timed cycle will keep icing the condenser on those wet 38-degree mornings Selma gets all winter, and that forces the unit onto strip heat, which shows up on the bill.
Coil Cleaning and Capacitor Testing
Valley dust and orchard particulate from the fields around Kingsburg and Parlier settle into the coil and throw off pressure readings. We wash it out, then test the capacitor under load. A capacitor reading under spec by even a few percent can mask as a refrigerant problem and get a homeowner sold a charge they didn’t need.
Geothermal Heat Pump Installation in Selma
Geothermal Heat Pump Installation in Selma is a different animal from an air-source swap. It involves a ground loop, either horizontal or drilled, and it’s more expensive upfront. You’re looking at a range that starts around $20,000 and goes up depending on lot size, soil conditions, and drilling depth. But it can cut heating and cooling costs by 40 – 60% compared to a standard air-source unit, and the ground loop typically lasts 50 years or more.
Selma’s flat valley terrain makes horizontal loops viable on larger residential lots, especially north of downtown where parcels run wider. If you have the land, the install gets simpler and cheaper. If you’re on a tighter city lot, vertical drilling works but costs more per foot.
Why We Run a Load Calculation First
Geothermal gets sized by the home’s actual heat loss and gain, not by matching the old unit. We run a Manual J load calculation on every quote. Oversizing a geothermal loop is wasted drilling, undersizing it means you’re running auxiliary heat through the winter fog.
What the Rebate and Financing Picture Looks Like
Geothermal systems qualify for federal tax credits and often local utility rebates. We handle the paperwork on our installs. The written quote we give you includes the installed price, any rebates we’ve verified, and what the system should cost to run.
Trusted Brands We Service in Selma
We install and service Trane, Goodman, and Rheem heat pumps regularly, and we’re factory-trained across brands including Lennox. If you already have a Trane air handler in a Selma home and want to keep the match, we can do that. We’re also set up to get parts fast for all three brands, which matters when a defrost board fails in the middle of a foggy stretch and the backup strip heat is running your meter up.
We carry common replacement parts for Trane and Goodman units specifically for our Selma service route. That means a failing capacitor or a stuck defrost sensor often gets fixed on the first visit instead of waiting on a parts order from Fresno.
Common Heat Pump Installation Problems We See in Selma Homes
We walk into the same handful of bad installs and misdiagnosed systems across Selma. Here’s what we find and what we do differently:
- Oversized tonnage sold without a load calculation. A ranch on a 6,000-square-foot lot off Rose Avenue gets quoted a 4-ton unit because the old one was 4-ton. The house only needs 2.5 tons. Short cycles, poor dehumidification, and a compressor that wears out early. We run the load calculation before we quote anything.
- Defrost board stuck in timed mode. Selma’s winter mornings hold at 95%+ humidity in the 35 – 45 degree range, so heat pumps here need on-demand defrost, not a fixed 30-minute timer. Timed mode ices the coil, trips the system onto strip heat, and pushes a $180 monthly electric bill to $400 in January.
- Condenser coil fouled by valley dust. Properties near the orchards and open fields around Floral Avenue and Mountain View Avenue get more particulate in the coil than most Fresno jobs. A dirty coil inflates refrigerant pressure readings, and too many techs add charge instead of cleaning the coil first.
- Mismatched air handlers and condensers. We see Goodman condensers paired with off-brand air handlers on Selma rentals, which kills efficiency and voids the manufacturer’s warranty. We match the system correctly or, if it’s a repair, tell you honestly whether the mismatch is worth correcting now or at replacement.
Pricing for Heat Pump Installation in Selma, CA
Here’s where the money actually goes on a Selma heat pump job. We quote these ranges up front, in writing, and they hold whether it’s the downtown corridor or out toward Kingsburg.
| Service | Selma Price Range |
|---|---|
| AC Repair | $150 – $650 |
| Furnace Repair | $150 – $700 |
| AC Installation | $3,500 – $7,500 |
| Tune-Up | $80 – $200 |
What moves a heat pump installation from the low end to the high end of that $3,500 – $7,500 range? Equipment tier, ductwork modifications, and whether the existing electrical panel needs an upgrade to handle the new unit’s startup draw. Homes in Selma’s older neighborhoods, especially those with original 1960s panels, sometimes need a breaker upgrade before the new heat pump goes in. We include that in the written quote before any work starts, so there’s no surprise line item.
Every estimate is free. Call (361) 306-9515 and we’ll schedule a time that works.
We Also Serve Cities Near Selma
Our heat pump crews cover Selma and the surrounding cities: Fowler, Parlier, Kingsburg, and Reedley. If you’re in one of those towns and need a heat pump installed, the same written pricing and 365-Day Done Right Promise apply.
Serving Selma, CA - Our Local Coverage Area
We’re based in the Selma area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Heat Pump Installation in Selma
Yes, a heat pump makes sense for most Selma homes because winters rarely dip below freezing for long, and the valley’s summer heat means you’re running air conditioning for five months straight. A modern cold-climate heat pump handles Selma’s 35 – 45 degree foggy mornings fine, though you’ll want the defrost board set to on-demand rather than a timed cycle. The real question is whether your electrical panel and ductwork are ready, which we check during the free estimate. Call (361) 306-9515 for a written quote.
Because Selma sits in the San Joaquin Valley’s heavy fog belt, and when the overnight temperature drops into the 35 – 45 degree range with fog at 95%+ humidity, moisture condenses and freezes on the outdoor coil. The heat pump has to reverse briefly to thaw that frost. If it’s defrosting every morning and your electric bill is climbing, the defrost board may be stuck in timed mode, which cycles defrost whether the coil needs it or not. We can set it to on-demand and test the sensors. Call (361) 306-9515 for service in Selma.
If the compressor or condenser coil has failed, replacement usually beats repair on a system over 10 years old. For Selma’s stock of 15-to-20-year-old units, a compressor replacement can run $1,800 – $2,800, and you’re still looking at an aging coil and defrost board behind it. On a unit under 8 years old, our Furnace Repair in Selma for a capacitor, defrost sensor, or contactor typically runs $150 – $650, and we’d fix it. We’ll give you the repair cost and the replacement cost side by side, in writing, so you can decide without pressure. Call (361) 306-9515.
SEER2 is the updated efficiency rating that accounts for real-world duct losses and static pressure, and it’s the number that matters starting in 2025 for new equipment. Going from a 14 SEER2 unit to an 18 SEER2 heat pump on a typical 1,800-square-foot Selma home can cut cooling costs by roughly 20 – 25% over a season, depending on your duct condition and insulation. We’ll show you the efficiency math for your specific home before you pick equipment. Call (361) 306-9515 for a free estimate.
We run a Manual J load calculation on every new heat pump installation in Selma, no exceptions. Matching old tonnage is exactly how homes end up with 4-ton units short-cycling on a house that needs 2.5 tons. The load calculation accounts for window area, insulation, duct leakage, and orientation, and it’s the only way to get sizing right on Selma’s older homes and the newer builds east of Highway 99. The calculation is included in the free estimate. Call (361) 306-9515 to schedule a visit.
Call Dalton Heating & Air for Heat Pump Installation in Selma
If you’re in Selma and your heat pump has been running strip heat through the fog, or you’re ready to stop patching an old unit and get a written price for a new one, call (361) 306-9515. We answer live, 24/7. Our estimator will come out, run the load calculation, and hand you a price in writing before any work begins. Every installation is backed by the 365-Day Done Right Promise, and our technicians arrive inside the stated window, uniformed and background-checked.
We service all of Selma, plus Fowler, Parlier, Kingsburg, and Reedley. For heat pump installation, geothermal, or maintenance, call Dalton Heating & Air at (361) 306-9515.
Written by Marco Benitez, Owner at Dalton Heating & Air, serving Selma and the Central Valley.